Product specifications

ManualsBrandsPOSline ManualsBarcode ReaderSW2500

Programming Manual

SW2500

WIRELESS SCANNER

Product specications are subject to change without notice.

Summary of content (72 pages)

PAGE 1
SW2500 WIRELESS SCANNER Programming Manual Product specifications are subject to change without notice.
PAGE 2
NOTICE This device complies with part 15 of the FCC Rules. Operation is subject to the following two condition: (1) This device may not cause harmful interface, and (2) This device must accept any interface received, including Interface that may cause undesired operation. This equipment has been tested and found comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 3
Operation Manual 2
PAGE 4
Index 1 Instroduction 4 Installation4 Recommended Steps 4 Configuration Flowchart 5 String Output Flowchart 5 Default Setting 6 Manual Label Layout 7 Frequent Question 8 2 Interface 10 Host Interface 10 Keyboard Wed
PAGE 5
Installation 1) First of all, you must make sure that the power is disconnected form your equipment before connecting the scanner. Beside, you also have to check the cable connector of the scanner match your equipment interface correctly. 2) Boot up your computer after connecting the scanner with your equipment, the scanner will make a long music and light the LED, above scanner to indicate a successful power on. Trigger the button, the scan line in front of scanner will active.
PAGE 6
Configuration Flowchart Set ASCII Code Hexdecimal (High Byte) Prefix or Suffix Hexdecimal O l (Low Byte) Set Decimal Value Decimal (10's Value) Decimal (1's Value) Finish ASCII Code or Decimal Value Setting SET EXIT Exit With Save ABORT Exit Without Save DEFAULT Exit & Default VERSION DATE Exit & Version SETTING LIST Interface Default Exit & Setting List Exit & Interface Default String Output Flowchart Preamble Prefix Code Name Code ID Code Length Code Data Suffix Postamble 5 Introduction Se
PAGE 7
Default Setting Code Read Length Truncate Code Type Enable Min. Max.
PAGE 8
Manual Label Layout Exit Program Function Title EXIT */$%END* UPC-A Truncate Leading Zero Group Line Disable DZA Enable DZB Selection Label *DZA* *DZB* Default Setting Spare Function Disable DYA Enable DYB Selection Description *DYA* Function Description *DYB* Adjustment (ASCII Code or Decimal Value) Specific Adjustments *BAO* (Range:0010-1510) Truncate Ending BAP *BAP* (Range:0010-1510) Code ID AAA *AAA* (Range:0016-FF16 ASCII Code) Code Option Code ID: A Code ID is a charact
PAGE 9
Frequent Question Q: Why scanner block the keyboard operation? A: Check the cable connection with your equipment, then turn power on again. Q: If scanner has a good read beep but nothing transferring after read a label. A: Using the SETTING LIST at 10 to show what current setting of scanner is, or reset to Default, (or select right Interface default if scanner to be change another interface used), then re-program scanner again.
PAGE 10
Example Beep Loudness Level "10", Good-read Beep "Enable" To configure the reguired commands proceed as follows: Send as: (1B16) B Command(s) B (0D16) Send B BAC B %01 B %00 B %OK B CEB B ︸︸︸︸︸ Beep 1 0 SET Good-read Londness Level Beep Enable ( Call to the dealer if scanner dose not work properly. 9 Introduction Q: How to configure scanner via RS-232C? A: Next to the selection description, you will find a frame command, such as AAB.
PAGE 11
PROGRAM */$%STR* Host Interface Interface Default Keyboard Wedge */$%C00* RS-232C */$%C01* WAND EMULATION */$%C02* You can change factory interface default for other type interface. By plug different cable, program scanner and set right interface to exit, then the scanner will be change to another interface. However, you must make sure what cable you need. Refer Cable Type to 66, 67.
PAGE 12
EXIT Keyboard Wedge */$%END* Keyboard Speed Low CZA *CZA* Medium CZB *CZB* CZC Turbo CZD *CZC* *CZD* Function Key Simulation Set Enable scanner can output code as pressing function-key in your application program while the barcode datas contain ASCII value between 0116 to 1F16.. See 60 and Refer to ASCII table 71 at grey area. You'll find function-keys with ASCII codes.
PAGE 13
PROGRAM */$%STR* Keyboard Wedge Keyboard Simulation Disable DCA *DCA* Enable DCB *DCB* All of the PCs check the keyboard status during power-on selftest. It is recommended to Enable the function if you are working without keyboard installation. It simulates keyboard timing and pass keyboard present status to the PC during power-on. Spare Function Disable DEA *DEA* Enable DEB *DEB* Specific Adjustments BAL Inter-char.
PAGE 14
EXIT Keyboard Wedge */$%END* Keyboard Type Select keyboard type connector of your host computer. Scanner must be selected to the appropriate host interface cable converter. Refer to Cable Type at 66. IBM AT,PS/2 DFA IBM XT DFB *DFA* *DFB* DFC DFD *DFD* NEC 9801 DFE *DFE* IBM PS/2 55 DFF *DFF* IBM 5550 DFG *DFG* KT 106 DFH *DFH* IBM 5576 DFI *DFI* Spare1 DFJ *DFJ* Spare2 DFK *DFK* Spare3 DFL *DFL* Spare4 DFM *DFM* 13 Interface *DFC* IBM PS/2 25,30 2 Macintosh ADB.
PAGE 15
PROGRAM */$%STR* Keyboard Wedge Keyboard Layout DGA USA (US) *DGA* DGB Belgium (BE) *DGB* DGC Danish (DK) *DGC* DGD France(FR) *DGD* DGE The selecting of keyboard layout supports many country languages other than USA keyboard layout. First you need to confirm country langage that you desire. In DOS, using command "Keyb" to selecte the desirable keyboard layout or in WINDOWS entry "Control' then pop "Keyboard" to selecte country at "language" item.
PAGE 16
EXIT */$%END* RS-232C Handshaking Protocol CTS: RTS: STX: ETX: Xon: Xoff: Clear To Send Request To Send Start Of Text End Of Text Transmit On Transmit Off (Hardware Signal) (Hardware Signal) (ASCII Code 0216) (ASCII Code 0316) (ASCII Code 1316) (ASCII Code 1116) Scanner Ready: The scanner will active the RTS signal after power-on, and will transmit data upon receiving active CTS signals.
PAGE 17
PROGRAM */$%STR* RS-232C Baud Rate DHA 38400 Bps *DHA* DHB 19200 Bps *DHB* DHC 9600 Bps *DHC* DHD 4800 Bps *DHD* DHE 2400 Bps *DHE* DHF 1200 Bps *DHF* DHG 600 Bps *DHG* DHH 300 Bps *DHH* Data Parity DKA None *DKA* DKC Even *DKC* DKD Odd *DKD* DKE Space *DKE* DKF Mark *DKF* Operation Manual 16
PAGE 18
EXIT */$%END* RS-232C Data Bits 7 Bits DJA *DJA* 8 Bits DJB *DJB* 2 Stop Bits DIA Two Bits DIB *DIA* *DIB* Specific Adjustments Inter-char. Delay: It is delay time between data character's output. It is same as Inter-char. Delay of keyboard wedge, see 12. Inter-char. Delay *BAL* (Range:0010-9910 Unit:1ms) Transmit Delay Transmit Delay: It is a delay time between barcode data output. It is also same as Transmit Delay of Keyboard wedge, see 12.
PAGE 19
PROGRAM */$%STR* Wand Emulation Active Level DMA Bar Hi/Space Lo *DMA* DMB Bar Lo/Space Hi *DMB* Bar Hi/Space Lo: Black will be transmited as a high voltage level (+5V) and space as low level (0V). Bar Lo/Space Hi: Black will be transmited as a low voltage level (0V) and space as high level (+5V). Normal Level DNA Low *DNA* DNB High *DNB* You must make sure what is Normal Level of your wand decoder device in stand-by (idle).
PAGE 20
EXIT Wand Emulation */$%END* Inter-char. Gap Narrow DPA Wide DPB *DPA* *DPB* Code-39 Simulation Disable DRA Enable DRB *DRA* *DRB* Specific Adjustments Margin Delay: It is a timer of zone like space zone of barcode label margin. The width of margin time will be added before and after in each barcode data automatically when it is transmitted.
PAGE 21
PROGRAM */$%STR* OCIA Protocol Type DSA NCR *DSA* DSB DTS *DSB* DSC NCR+ASCII *DSC* DSD DTS+ASCII *DSD* DSE ASCII *DSE* Data Parity DTA Even *DTA* DTB Odd *DTB* DTC Space *DTC* DTD Mark *DTD* Spare Function DUA Disable *DUA* DUB Enable *DUB* Specific Adjustments BAM Transmit Delay *BAM* (Range:0010-9910 Unit:10ms) Operation Manual Tansmit Delay: It is a delay time between barcode data output. It is also the same as Transmit Delay of keyboard wedge, see 12.
PAGE 22
EXIT System Control */$%END* Power-on Music After power-on the scanner will generate music to indicate the successful selftest. You can inhibit the music by setting Disable . Disable CBA *CBA* Enable CBA *CBB* Power-on Auto Trigger By setting Enable , the scanner will activate the light source after the power-on without trigger button.
PAGE 23
PROGRAM */$%STR* System Control Double Confirm CSA Disable *CSA* CSB Enable *CSB* The scanner will require many times of successful decoding to confirm the barcode data, and the more confirm times the more inhibitive mis-reading code. (Refer to setting of Doubble Confirm Times at 25) Case Conversion CTA Disable *CTA* CTC Uppercase *CTC* CTD Lowercase *CTD* It converses all output characters to be same printing-case, even they have two kinds of case within a barcode data.
PAGE 24
EXIT System Control */$%END* Scanning Mode Good-read Off: The trigger button must be pressed to active scanning. The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand-by Timer 24 duration elapsed. (Laser Model Default) Momentary: The trigger button acts as a switch. Press button to active scanning and release button stop scanning.
PAGE 25
PROGRAM */$%STR* System Control Specific Adjustments BAC Beep Loudness *BAC* (Range:0110-1010 Unit:Level) BAD Beep Tone *BAD* (Range:0510-5010 Unit:100Hz) BAE Beep Duration *BAE* (Range:0110-9910 Unit:10ms) BDA Beep Tone1 *BDA* (Range:0510-5010 Unit:100Hz) BDB Beep Duration1 *BDB* (Range:0010-9910 Unit:10ms) BAF Stand-by Time *BAF* (Range:0110-9910 Unit:1s) BAG Active Time *BAG* (Range:1010-9910 Unit:10ms) BAH Beep Adjustments: You can adjust Beep Loudness , Beep Tone and Beep Durat
PAGE 26
EXIT System Control */$%END* Specific Adjustments Add-on Waiting Time: This setting is Addon-Waiting Time BAK only used for reading WPC symbologies with Add-on, such as (Range:0110-9910 Unit:10ms) EAN and UPC. The WPC must be decoded first, then Add-on. But Double Confirm Times BAJ Add-on may not decode very well during it read. Therefore, scanner (Range:0110-9910) offer a waiting time for reading Add-on Public Min. Length BAA confirmation and transmits WPC with Add-on at the same time.
PAGE 27
PROGRAM */$%STR* UPC-A Read Disable DVA Format *DVA* Leading Data Digts Check Zero (11 Digits) Digit Enable DVB *DVB* Add-on DWA Disable *DWA* DWB Add-on 2 Only *DWB* DWC Add-on 5 Only *DWC* DWD The Add-on barcode is the supplemental 2 or 5 characters for WPC code. Format Leading Data Digits Check Add-on Zero (11 Digits) Digit 2 or 5 Add-on 2 or 5 *DWD* Waiting Add-on DXA Disable *DXA* DXB Enable *DXB* It is recommended to set Enable if the WPC with Add-on code must be read together.
PAGE 28
EXIT */$%END* UPC-A Truncate Leading Zero The leading "0" digits of barcode data characters can be truncated when the function is enabled.
PAGE 29
PROGRAM */$%STR* UPC-E Read ECA Disable Format *ECA* ECB Leading Data Digits Check Zero (6 Digits) Digit Enable *ECB* Add-on EDA Disable Format *EDA* EDB Leading Data Digits Check Add-on Zero (6 Digits) Digit 2 or 5 Add-on 2 Only *EDB* EDC Add-on 5 Only *EDC* EDD Add-on 2 or 5 *EDD* Waiting Add-on EEA Disable Refer to 26. *EEA* EEB Enable *EEB* Expansion EFA Disable *EFA* EFB Enable The expansion function is used only for UPC-E and EAN-8 code reading.
PAGE 30
EXIT */$%END* UPC-E Check Digit Refer to 26. Disable EIA *EIA* Enable EIB *EIB* Truncate Leading Zero Refer to 27. Disable EHA Enable EHB *EHA* *EHB* Spare Function Enable EGB *EGA* *EGB* Specific Adjustments Refer to 27.
PAGE 31
PROGRAM */$%STR* EAN-13 Read EKA Disable Format *EKA* EKB Data Digts Check (12 Digits) Digit Enable *EKB* Add-on ELA Disable Format *ELA* ELB Data Digits Check Add-on (12 Digits) Digit 2 or 5 Add-on 2 Only *ELB* ELC Add-on 5 Only *ELC* ELD Add-on 2 or 5 *ELD* Waiting Add-on EMA Disable Refer to 26.
PAGE 32
EXIT */$%END* EAN-13 Check Digit Refer to 26. Disable EQA *EQA* Enable EQB *EQB* Truncate Leading Zero Refer to 27. Disable EPA Enable EPB *EPA* *EPB* Spare Function Enable EOB *EOA* *EOB* Specific Adjustments Refer to 27.
PAGE 33
PROGRAM */$%STR* EAN-8 Read ESA Disable Format *ESA* ESB Data Digits Check (7 Digits) Digit Enable *ESB* Add-on ETA Disable Format *ETA* ETB Data Digits Check Add-on (7 Digits) Digit 2 or 5 Add-on 2 Only *ETB* ETC Add-on 5 Only *ETC* ETD Add-on 2 or 5 *ETD* Waiting Add-on EUA Disable Refer to 26. *EUA* EUB Enable *EUB* Expansion EVA Disable Refer to 28.
PAGE 34
EXIT */$%END* EAN-8 Check Digit Refer to 26. Disable EYA *EYA* Enable EYB *EYB* Truncate Leading Zero Refer to 27 Disable EXA Enable EXB *EXA* *EXB* Spare Function Enable EWB *EWA* *EWB* Specific Adjustments Refer to 27.
PAGE 35
PROGRAM */$%STR* CODE-39 Read FAA Disable *FAA* FAB Enable Format Start Data Digits Checksum End "8" (Variable) (Optional) "8" *FAB* Format FBA Standard *FBA* FBB Full ASCII *FBB* The Full ASCII Code-39 is an enhanced set of Code-39 that is the data with toatl of 128 characters to represent Full ASCII code. It is combined one of the digits +,%,$ and / with one of the alpha digits (A to Z).
PAGE 36
EXIT */$%END* CODE-39 Checksum Verification The checksum of Code-39 is optional and made as the sum module 43 of the numerical value of the data digits. Disable FGA Enable FGB *FGA* *FGB* Checksum Transmission By setting Enable , checksum and will be transmitted. Disable FHA Enable FHB *FHA* *FHB* Specific Adjustments *BAY* (Range:0010-1510) Truncate Ending BAZ *BAZ* (Range:0010-1510) Min. Code Length BAW *BAW* (Range:0110-5610) Max.
PAGE 37
PROGRAM */$%STR* Interleaved 2 of 5 Read FKA Disable Format *FKA* FKB Data Digits Checksum (Variable) (Optional) Enable *FKB* Format FLA Standard *FLA* FLB Odd S-code *FLB* Generally, the Interleaved 2 of 5 symbology is a pair of digts in each barcode. Therefore, it contains an even digits. If the symbol is present an odd number as S-code, then Odd S-code have to select.
PAGE 38
EXIT Interleaved 2 of 5 */$%END* Specific Adjustments Because, the start and end of interleaved 2 of 5 code is not olny one patten in symbol. In order to prevent partial reading, it is recommand to use the fixed code length for each 2 of 5 code barcode label. Setting the same Min./Max. Code Length , it is like a length filter, and only one length is accepted. Truncate Leading BBC *BBC* (Range:0010-1510) Truncate Ending BBD *BBD* (Range:0010-1510) Min. Code Length BBA *BBA* Refer to 27, 35.
PAGE 39
PROGRAM */$%STR* Industrial 2 of 5 Read FQA Disable Format *FQA* FQB Data Digits Checksum (Variable) (Optional) Enable *FQB* Checksum Verification FSA Disable *FSA* FSB The checksum is made as the sum module 10 of the numberical values of all data digits. Enable *FSB* Checksum Transmission FTA Disable Refer to 35.
PAGE 40
EXIT Industrial 2 of 5 */$%END* Specific Adjustments Refer to 27, 35. Truncate Leading BBG *BBG* (Range:0010-1510) Truncate Ending BBH *BBH* (Range:0010-1510) Min. Code Length BBE *BBE* (Range:0010-5610) Max.
PAGE 41
PROGRAM */$%STR* Matrix 2 of 5 Read FVA Disable Format *FVA* FVB Data Digits Checksum (Variable) (Optional) Enable *FVB* Checksum Verification FXA Disable *FXA* FXB The checksum is made as the sum module 10 of the numberical values of all data digits. Enable *FXB* Checksum Transmission FYA Disable Refer to 35.
PAGE 42
EXIT */$%END* Matrix 2 of 5 Specific Adjustments Refer to 27, 35. Truncate Leading BBK *BBK* (Range:0010-1510) Truncate Ending BBL *BBL* (Range:0010-1510) Min. Code Length BBI *BBI* (Range:0010-5610) Max.
PAGE 43
PROGRAM */$%STR* China Post 2 of 5 Read GAA Disable Format *GAA* GAB Data Digits Checksum (Variable) (Optional) Enable *GAB* Checksum Verification GCA Disable *GCA* GCB The checksum is made as the sum module 10 of the numberical values of all data digits. Enable *GCB* Checksum Transmission GDA Disable Refer to 35.
PAGE 44
EXIT China Post 2 of 5 */$%END* Specific Adjustments The code length of Post 2 of 5 is always fixed at 11. Therefore, code length of Min. and Max. is also factory default is 11. Truncate Leading BBO *BBO* (Range:0010-1510) Truncate Ending Refer to 27, 35. BBP *BBP* (Range:0010-1510) Min. Code Length BBM *BBM* (Range:0010-5610) Max.
PAGE 45
PROGRAM */$%STR* Codabar/NW7 Read GFA Disable *GFA* GFB Enable Format Start Data Digits Cheksum End (Variable) (Optional) *GFB* Start/End Symbol Types GGA ABCD/ABCD *GGA* GGB The Codabar has four pairs of Start/End patten, you may choice one to match your application. abcd/abcd *GGB* GGC ABCD/TN*E *GGC* GGD abcd/tn*e *GGD* Same Start/End Pair GHA Disable *GHA* GHB Sometime, the Codabar requires only same Start/End patten of barcode label to be decoded.
PAGE 46
EXIT */$%END* Codabar/NW7 Checksum Transmission Refer to 35. Disable GKA Enable GKB *GKA* *GKB* Specific Adjustments Refer to 27, 35. Truncate Leading BBS *BBS* (Range:0010-1510) Truncate Ending BBT *BBT* (Range:0010-1510) Min. Code Length BBQ (Range:0010-5610) *BBR* (Range:0010-5610) Code ID AAL *AAL* (Range:0016-FF16 ASCII Code) Insertion Group BDL *BDL* (Range:0010-9910) 45 Code Option Max.
PAGE 47
PROGRAM */$%STR* Code-128 Read GMA Disable Format *GMA* GMB Data Digits Checksum (Variable) (Optional) Enable *GMB* Format GNA Standard *GNA* GNB UCC/EAN-128 *GNB* The Code-128 can be translated to UCC/EAN-128 format if it starts with FNC1 character. The first FNC1 will be translated to "]C1", and next to be a concatenation code as (7F16).
PAGE 48
EXIT */$%END* Code-128 Spare Function Disable GPA Enable GPB *GPA* *GPB* Specific Adjustments Concatenation Data: This featrure is only used for UCC/EAN-128 format. This Concatenation Data means you can re-assign second or after a FNC1 for your usage. The default of ASCII code is (1D16). Truncate Leading BBW *BBW* (Range:0010-1510) Truncate Ending BBX *BBX* (Range:0010-1510) Refer to 27, 35. Min.
PAGE 49
PROGRAM */$%STR* Code-93 Read GTA Disable *GTA* GTB Enable Format Data Digits Checksum1 Checksum2 (Variable) (Optional) (Optional) *GTB* Append GVA Disable *GVA* GVB This function which allows several symbols to be concatenates and be treated as one single data entry. Enable *GVB* Checksum Verification GWA Disable *GWA* GWC The checksum is presented as the sum module 47 of all data digits. One *GWC* GWD Two *GWD* Checksum Transmission GXA Disable Refer to 35.
PAGE 50
EXIT */$%END* Code-93 Specific Adjustments Refer to 27, 35. Truncate Leading BCA *BCA* (Range:0010-1510) Truncate Ending BCB *BCB* (Range:0010-1510) Min. Code Length BBY *BBY* (Range:0010-5610) Max.
PAGE 51
PROGRAM */$%STR* Code-11 Read GZA Disable *GZA* GZB Enable Format Data Digits Checksum1 Checksum2 (Variable) (Optional) (Optional) *GZB* Checksum Verification HBA Disable *HBA* HBC The checksum is presented as the sum module 11 of all data digits. One *HBC* HBD Two *HBD* Checksum Transmission HCA Disable *HCA* HCB Enable By setting Enable , checksum1 and checksum2 will be transmitted upon your selected checksum verificvation mothod.
PAGE 52
EXIT */$%END* Code-11 Specific Adjustments Refer to 27, 35. Truncate Leading BCE *BCE* (Range:0010-1510) Truncate Ending BCF *BCF* (Range:0010-1510) Min. Code Length BCC *BCC* (Range:0010-5610) Max.
PAGE 53
PROGRAM */$%STR* MSI/Plessey Read HEA Disable *HEA* HEB Enable Format Data Digits Checksum1 Checksum2 (Variable) (Optional) (Optional) *HEB* Checksum Verification HGA Disable *HGA* HGB Mod 10 *HGB* HGC Mod 10/10 *HGC* HGD The MSI/Plessey has one or two optional checksum digits. The checksum is presented 3 kinds of mothod Mod 10 , Mod 10/10 and Mod 11/10 . The checksum1 and checksum2 will be calculated as the sum module 10 or 11 of the data digits.
PAGE 54
EXIT */$%END* MSI/Plessey Specific Adjustments Refer to 27, 35. Truncate Leading BCI *BCI* (Range:0010-1510) Truncate Ending BCJ *BCJ* (Range:0010-1510) Min. Code Length BCG *BCG* (Range:0010-5610) Max.
PAGE 55
PROGRAM */$%STR* UK/Plessey Read HQA Disable Format *HQA* HQB Data Digits Checksum1+2 (Variable) (Optional) Enable *HQB* Checksum Verification HSA Disable *HSA* HSB Enable *HSB* Checksum Transmission HTA Disable Refer to 35.
PAGE 56
EXIT */$%END* UK/Plessey Specific Adjustments Refer to 27, 35. Truncate Leading BCQ *BCQ* (Range:0010-1510) Truncate Ending BCR *BCR* (Range:0010-1510) Min. Code Length BCO *BCO* (Range:0010-5610) Max.
PAGE 57
PROGRAM */$%STR* IATA Read HJA Disable *HJA* HJB IATA (International Air Transport Association) Enable *HJB* Checksum Verification HNA Disable *HNA* HNB The checksum is presented as sum module 7 of all data digits. Enable *HNB* Checksum Transmission HOA Disable Refer to 35.
PAGE 58
EXIT */$%END* IATA Specific Adjustments Refer to 27, 35. Truncate Leading BCM *BCM* (Range:0010-1510) Truncate Ending BCN *BCN* (Range:0010-1510) Min. Code Length BCK *BCK* (Range:0010-5610) Max.
PAGE 59
PROGRAM */$%STR* Telepen Read HVA Disable Format *HVA* HVB Data Digits Checksum (Variable) (Optional) Enable *HVB* Format HWA Numeric Only *HWA* HWB Full ASCII Only *HWB* HWC Auto Switching *HWC* A Telepen can be transimtted with and Full ASCII format. Characters can be mixed both formats inside barcode label of Telepen. By setting Auto Switching , datas can be conversed between Numeric and Full ASCII by character (7F16) automatically.
PAGE 60
EXIT */$%END* Telepen Specific Adjustments Refer to 27, 35. Truncate Leading BCU *BCU* (Range:0010-1510) Truncate Ending BCV *BCV* (Range:0010-1510) Min. Code Length BCS *BCS* (Range:0010-5610) Max.
PAGE 61
PROGRAM */$%STR* Preamble/Postamble Preamble Transmission Disable IEA *IEA* Enable IEB By setting Enable , Preamble will be appended before the data transmitted. Refer to String Output Flowchart at 5. *IEB* Preamble Data Data1 AAZ *AAZ* (Range:0016-FF16 ASCII Code) Data2 ABA *ABA* There are two control characters ( Data1 and Data2 ) can be programmed for both Preamble and Postamble datas. They are appended to the data automatically when each barcode is decoded.
PAGE 62
EXIT */$%END* Prefix/Suffix Prefix Transmission Up to 15 characters can be programed for Prefix data. The Prefix data of string will be placed after Preamble data and before the barcode data when it is Enable . Refer to String Output Flowchart at 5. Disable IGA Enable IGB *IGA* *IGB* Clear All IMA *IMA* Prefix Data Data ABF *ABF* (Range:0016-FF16 ASCII Code) Suffix Transmission Up to 15 characters can be programed for Suffix datas.
PAGE 63
PROGRAM */$%STR* Character Insertion Add-on Insertion Disable IIA *IIA* Enable IIB *IIB* The scanner offers 2 characders of insertion between WPC and add-on code. Format WPC Add-on Insertion Add-on Add-on Insertion Data Data1 ABD *ABD* (Range:0016-FF16 ASCII Code) Data2 ABE *ABE* (Range:0016-FF16 ASCII Code) Insertion1 Data BCW Position1 *BCW* (Range:0110-4810) ABL Data1 *ABL* (Range:0016-FF16 ASCII Code) ABM The scanner offer 4 positions and 8 characters to insert among the symbol.
PAGE 64
EXIT */$%END* Character Insertion Insertion3 Data Position3 BCY *BCY* (Range:0010-1510) Data1 ABP *ABP* (Range:0016-FF16 ASCII Code) Data2 ABQ *ABQ* (Range:0016-FF16 ASCII Code) Insertion4 Data Example Barcode "1234567" Postion Data1 Data2 Insertion1 2 A B Insertion2 5 C D Position4 *BCZ* (Range:0010-1510) Data1 1) PROGRAM B ABR *ABR* Entry programming 2) Position1 B 0 B 2 B SET "2" BCZ (Range:0016-FF16 ASCII Code) Position1 Data2 ABS (Range:0016-FF16 ASCII Code) 5) Data1 B 4 B 3 B
PAGE 65
PROGRAM */$%STR* Other Control Code ID Translation IBA Disable *IBA* IBB If your application want to transmite Code ID, you must set this Enable . Enable *IBB* Code ID Position ICA Before Code Data *ICA* ICB After Code Data Upon your usage, the transmitting position of Code ID can be selected to place Before or After Code Data when it transmitted.
PAGE 66
EXIT */$%END* Other Control Inverse PROGRAM If scanner is operated in inverse barcode reading, use inverse PROGRAM to entry scanner programming. PROGRAM */$%STR* Normal/Inverse Barcode Generally, the scanner can only read positive barcode signals which are printed black on white (call normal barcode). By setting Inverse Barcode , the scanner will read negative barcode which bars are printed with light color and spaces with dark color (call inverse barcode).
PAGE 67
Cable Type IBM PC, XT, AT & PS/2 Function 5p Din(M) 5p Din(F) 6p Mini Din(M) 6p Mini Din(F) Clock (Host) 1 --5 --Data (Host) 3 --1 --Clock (KBD.) --1 --5 Data (KBD.
PAGE 68
Cable Type RS-232C Function 9p D-Sub(F) 25p D-Sub(F) 8p Din(M) DC Jack(M) TxD 2 3 1 --RxD 3 2 2 --RTS 8 5 3 --CTS 7 4 4 --Shorted 4,6 6,20 ----Ground 5 7 7 2 GND Shield 5 7 7 2 VCC (+5V) 9 16,25 8 1 5 8 5 3 14 7 1 13 9 6 25 9p D-Sub(F) 1 2 4 1 6 1 25p D-Sub(F) 8p Din(M) 2 DC Jack(M) Wand Emulation Function Data Ground GND Shield VCC (+5V) 9p D-Sub(F) 2 7 8 9 5 5p Din(M) 2 3 3 1 1 9 3 2 1 4 5 6 9p D-Sub(F) 6p Din(M) 2 3 3 1 3 2 1 6 4 5 5p Din(M) 6p Din(M) 6 TTL (CMOS) 4 5 5p Din(
PAGE 69
Test Chart UPC-A 000012345670 EAN-13 (ISBN) with Add-on 5 9789572216675 00420 (ISBN: 9572216678) Code-39 (Full ASCII Code) * C O D E 3 9 T + E + S + T * ( F u l l A S C I I C o d e : * C O D E 3 9 Te s t * ) Interleaved 2 of 5 12345678905 Code-93 CODE93 TESTYd Code-128 (C Type) 0123456789e (UCC/EAN-128: ]C10123456789e) Operation Manual 68
PAGE 70
Test Chart Codabar/NW7 C98765D D43210A MSI/Plessey 1 0 5 5 8 3 0 2 5 CODE-11 8 8 6 2 6 4 7 7 7 9 7 3 3 UK/Plessey 1 6 5 2 0 0 0 3 5 4 6 1 Telepen 7 IATA 0 0 1 0 2 0 0 0 0 1 0 9 1 9 6 69 Test Chart T E L E P E N T e s t + (Numeric: 57424942534251055774888916)
PAGE 71
Operation Manual 70
PAGE 72
0 ASCII Code Table H 0 1 DLE F1 SOH DC1 Down F2 STX DC2 3 Left F3 ETX DC3 4 Right F4 EOT DC4 5 PgUp F5 ENQ NAK 6 PgDn F6 ACK SYN F7 BEL ETB 0 Null 1 Up 2 1 1 0 NUL L 7 8 Bs F8 BS CAN 9 Tab F9 HT EM F10 LF SUM A B Home Esc VT ESC C End F11 FF FS D Enter F12 CR GS E Insert Ctrl+ SO RS F Delete Alt+ SI US 2 3 4 5 6 7 8 For keyboard wedge only.