8070 Assembly Instructions Only for Joerns Bed model number 2003DC #B684DC modified for the Posey Bed U.S. Pat. No. 7,735,167 Rx ONLY Posey Company • 5635 Peck Road, Arcadia, CA 91006-0020 USA Phone: 1.800.447.6739 or 1.626.443.3143 • Fax: 1.800.767.3933 or 1.626.443.5014 • www.posey.
Table of Contents Introduction Replacement Parts Safety Instructions ................................................................ 3 Parts List...................................................................................20 Safety Precautions ................................................................ 3 Technical Specifications .....................................................4 Warranty General Information ............................................................
Introduction Safety Instructions Safety Precautions The Posey Bed Assembly Instructions include important instructions and information related to the assembly of the bed. It is important to read the Assembly Instructions carefully prior to assembly of the bed for the first time. Warnings, Cautions, and Notes are provided throughout this manual to indicate levels of potential hazards or helpful information as defined below.
Introduction Specifications for Joerns Bed model number 2003DC #B684DC modified for the Posey Bed Power Supply Requirements Model: Posey Bed 8070 Rated voltage and current: 108-132 VAC Frequency: 60Hz Current Rating: 1.6 Amps (110-120V unit) Classification: Class II, Type B (Double insulated) Circuit Protection: 250V, F1.36A (110-120V unit) Mode of Operation: 10% Maximum duty cycle Dimensions Highest Position Inches: Centimeters: 84.25(W) x 40.75(D) x 73.
Introduction General Information Installation This section provides detailed installation and setup instructions for the Posey Bed on the Joerns Bed model number 2003DC #B684DC modified for the Posey Bed. The installation steps must be followed correctly to ensure proper operation and service. Read these Assembly Instructions carefully before attempting to assemble the bed. Follow all instructions carefully. Gather assembly tools not included in the boxes.
Bed Assembly Unpacking the Parts ✔ Confirm that all parts have been included with the bed. If any items are missing or damaged, please contact Posey Technical Service at 1.800.447.6739. A C B D D Part Qty ✔ Description A 1 Hardware packet- 1” bolt & lock washers (12 ea.) B 1 Hardware packet- 1 ¼” carriage bolts, flat washers & nuts (8 ea.) C 1 Hardware packet- square plugs, lock washers & bolts (4 ea.) D 1 Hardware packet- 2” bolts & nuts (8 ea.
Bed Assembly Caster Leg Frame Assembly Materials: • Hardware Packet C • Parts J & K • 9/16” wrench 3. Press firmly to seat the caster leg frame (Part J) completely down into the wheel receiver (Fig. 2-C). J NOTE: Bed assembly should be done near an appropriate AC electrical outlet to assist with assembly. 1. Lay the bed frame (Part P) on the floor, upside down (Fig. 2-A). NOTE: Bed motor will be located on the foot end (Fig. 2-A). Head Side Foot Side J K P O Bed Motor P Fig. 2-C 4.
Bed Assembly 7. Place a lock washer on a 1” bolt (Hardware Packet C) and insert it into a square plug with channel fitting (Fig. 2-E). 9. Tighten with a 9/16” wrench (Fig. 2-G). Do not over tighten. Square Plug Locking Washer P 1” Bolt Fig. 2-E 8. Put the plug and bolt into the hole on top of the caster leg frame using the square plug and receiver (Fig. 2-F). Square Plug J Fig. 2-G 10. Repeat until all four square plugs have been installed. 1” Bolt Locking Washer Fig.
Bed Assembly Transfer Brake Assembly Materials: • Hardware Packet D • Part O (4) • 7/16” wrench (2) 4. Use a 7/16” wrench to tighten both bolts (Fig. 3-D). NOTE: Two 7/16” wrenches are needed: One to hold the bolt, and the other to hold the nut. Do NOT over tighten. 1. Align the top and bottom holes on the Transfer Brake (Part O) with the two holes on the bed frame. NOTE: Make sure the holes in the brake are facing the holes in the bed frame (Fig. 3-A). Fig. 3-D Top Hole O 5.
Bed Assembly Frame Assembly Materials: • Hardware Packet B • Part H-I, M-N • Clamps (4) • 7/16” wrench NOTE: The frame assembly consists of distinct left and right posts for both the head and foot of the bed frame. Each post is labeled with a letter for easy assembly. Reference the Posey Bed frame location to assist with assembly (Fig. 4-A) Frame assembly requires two people to provide stability and to help prevent injury.
Bed Assembly Left Head Post 1. Align the left head post (Part H) with the holes on the frame located on the left side, head of the bed (Fig. 4-J). H Hole Direction Inward Left Foot Post 1. Align the left foot post (Part M) with the holes on the frame located on the left side, foot of the bed (Fig. 4-N). M P H M J I Hole Direction Inward K N B B Fig. 4-M Fig. 4-J Fig. 4-I P Fig. 4-N NOTE: Make sure the holes on the posts face inward and towards the center (Fig. 4-I).
Bed Assembly Short Rail Assembly Materials: • Hardware Packet A • Part L (2) • 9/16” wrench Long Rail Assembly Materials: • Hardware Packet A • Part G (2) • 9/16” wrench This section requires two people. 1. Hold and align one of the short rails (Part L) between the left and right head posts (Parts H & I). NOTE: Make sure the holes on the posts face inward on both sides of the frame (Fig. 5-A). This section requires two people. 1.
Bed Assembly 4. Repeat on the other side of the rail. 5. Repeat with the second long rail between the right head and right foot posts (Parts I & N). 6. Tighten all bolts (short and long rails) with a 9/16” wrench until there is resistance (5-F). 8. The frame assembly is complete (Fig. 5-H). G L L G M H N I L G Fig. 5-H N Fig. 5-F 7. Gently hand shake each vertical post and top rails to ensure the bolts are securely fastened.
Bed Assembly Foam Pad Assembly 4. Repeat with the other long foam pad on the other side (Fig. 6-B). Materials: • Parts E (2), F (8) 1. Open the slot on a short foam pad (Part E) and wrap around the short rail at either the head or foot or the bed (Fig. 6-A). NOTE: Make sure that the slot faces outward from the bed frame. 5. Open the slot on a long foam pad (Part F) and wrap around on any of the vertical leg posts (Fig. 6-C). Make sure that the slot faces outward from the bed frame. 2.
Bed Assembly Canopy Installation 5. Pull the canopy material together and zip only half-way up (Fig. 7-D). Materials: • Part R (1) • Assembled Bed Frame NOTE: Zipping half-way assists with the installation of the top portion of the canopy. When zipping the canopy, make sure the zipper pins are completely seated. Failure to do this will prevent the zipper from closing securely, which may lead to unassisted bed exit and potential patient injury.
Bed Assembly Canopy Head End Flap Installation 1. Locate the Canopy Head End Flap at the head of the bed (Fig. 8-A). 2. Open the hook and loop and wrap around the metal end of the head of the bed (Fig. 8-B). Canopy Head End Flap Fig. 8-A 3. Secure the hook and loop (Fig. 8-B). Fig.
Bed Assembly Mattress Installation 4. Attach the canopy to the bed frame by securing both bed straps located in the middle of the long sides of the bed. Materials: • Part Q (1) • Assembled Bed Frame with Canopy If not using the Posey Bed 8070 mattress, a mattress that measures 6” x 35” x 80” (15 x 89 x 203 cm) must ONLY be used. Any other size mattress may result in patient injury or death. 1. Completely unzip the mattress compartment.
Bed Assembly Power Cord Attachment NOTE: If not already done, retrieve the power cord attachment taped to the underside of the bed. 4. Secure power cord with the power cord strap located at the head of the bed (Figs. 10-C, 10-D, & 10-E). 1. Attach the bed control to the canopy. 2. Place the bed control into one of the pockets near the foot of the bed (Fig. 10-A). Fig. 10-C Fig. 10-D Fig. 10-A 3. Secure the bed control with the bed control clip (Fig. 10-B). Fig. 10-E Fig.
Bed Assembly Assembly Check 1. The bed assembly is completed (Fig. 11-A). 2. Store all Posey Bed instructional material in the instruction storage pocket at the foot of the bed (Fig. 11-B). Posey Bed Instructions Storage Fig. 11-B Fig. 11-A Check: ✔ Bed frame feels secure with no loose or moving parts. ✔ All casters lock when caster lock is engaged. ✔ Lower bed to the lowest position to ensure transfer brakes engage securely. 3. The Posey Bed is now ready for delivery or storage.
Replacement Parts 8070 Replacement Parts Replacement Part Availability: Part No. A, B, C, D E F G H I J K L M N O P Q R Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Description Qty.
Limited Warranty Posey Limited Warranty What Does this Warranty Cover? Posey warrants to the original purchaser that the Posey Bed 8070 is free of defects in materials and workmanship. If the product is found to be defective in workmanship or materials, we will repair or replace it at our option at no charge, other than certain transportation and cleaning charges.
Technical Service Technical Service Posey Technical Service: We are happy to assist you between the hours of 6 AM and 5 PM Pacific Time, USA. Please call us at 1.800.44.POSEY (1.800.447.6739), or 1.626.443.3143. You can fax us at 1.800.767.3933, or 1.626.443.5014. Shipping: Ship items to Posey Company: 5635 Peck Road, Arcadia, CA 91006-0020 USA. Canopy Repairs. To prevent damage in shipping, clean the canopy and close all zippers. In-Warranty Repairs: 1.
Notes
Posey Company • 5635 Peck Road, Arcadia, CA 91006-0020 USA Phone: 1.800.447.6739 or 1.626.443.3143 • Fax: 1.800.767.3933 or 1.626.443.5014 • Web: www.posey.com © 2013 Posey Company. All rights reserved.
