OPERATION & INSTALLATION MANUAL GPS GPRS TRACKING AND ALARM SYSTEM TLU100N
REV: 1.9 (STANDARD, TLU100N-TLU200C-PTM-5.09-V1.27 TLU200C2) I. BRIEF INTRODUCTION TLU100N System utilizes the GPRS, GPS and car alarm functions in one unit. The unit continuously gets its precise position and speed information from GPS system. It automatically manages and monitors all of its peripheral equipment and their status all the time. It will send timely message to user if any predefined trigger occurs through GPRS network system.
2. Supplement message of report Some special reports have supplement message segment that begin with “CFG:”, for example: 1) Duty-On report: it has an additional User-ID segment. e.g.: %%8888,A,050929003153,N2240.6927E11359.3980,0,185,C+28,C3800000,151,CFG:1234 2) Duty-Off report: it has the following additional message segment. CFG: User-ID, Maximum speed, Average speed, Total trip distance, Total duration, Total over speed duration e.g.: %%8888,A,050929003153,N2240.6927E11359.
IV. BASIC FUNCTIONS FUNCTIONS GPS GPRS, SMS 5 input PC-setup Standard Report Event Report History data store V. APPLICATIONS GPS receiver will output a complete position, velocity, and time (PVT) solution in the NMEA Version 3.0 protocol GPRS use standard TCP or UDP communicate protocol. If the GPRS service is failed, the SMS mode will be turned on for emergency use. 1. Door TG2. general AD1 port 3. TG+ 4. Tamper switch 5.
4. Tamper switch: The tamper switch is used to check whether the box of host be opened or not, if so it will send out a relevant report. 5. Backup A/D: There is still 1 A/D input interface for potential use. VII. WIRELESS ACCESSORIES DESCRIPTION The TLU100N has now 3 kinds wireless equipments: wireless door sensor, wireless temperature sensor and wireless key pad. 1. Wireless Door magnetic sensor A: The unit can support up to 4 wireless magnetic door sensors.
3. The Wireless Keypad The Wireless Keypad was used for communication interface between user and TLU100N. It communicate with host by two-way RF, normally the keypad sends its command that user entered to host, if the command is accepted as a valid command then the host will send back a response as an ACK. The Key Pad has total 9 commands. And it has 4 main functions; they are Duty On/Off, Help Request, Self-Geofence setting and Wireless sensor ID learning.
IX. PC SETUP AND SYSTEM INITIATION 1. Brief PC SETUP Description The UNIT must be initialized by PORTMAN PC setup program in order to make communication with the remote server /call center. There are four main sections that allow users to program the device. 1) User detail (Device ID, server IP, and port, GPRS APN，4 SMS number….) 2. 3. 2) Geofence (9 circular Geofence and 1 Self Geofence, 20 point Geofence….
C. MAIN INTERFACE The following is the brief Button Description for main interface: (1) Initialize: clear all saved parameters in TLU100N. (2) Request All: request all parameters that is saved previously in TLU100N (3) Request: request parameters in the current page (4) Apply: set the parameters in the current page (5) Apply All: save all the parameters into TLU100N (6) Load: load the saved configuration file (*.ptm) (7) Save: save the parameters into a files (*.ptm).
2.[Geofence]: 1) Circle Geofence setting: Set circular Geofence parameters in left window. The data should be coordinate center of the Geofence and the related radius. 2) Point Geofence setting: Set point Geofence in right part of the window, only GPS coordinate point data is needed. 3) Self-Geofence setting: Self-Geofence is a fresh idea for vehicle guard. User need only input a circle radius in this field.
In normal working mode (DUTY ON), the system will use the configurations as defined in this section. To activate the automatic report, please select “√” in checkbox and fill in data in the textbox. The reports will be summarized as (1) Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. Report when speed less than a preset value (refer the following 1.5 Km/Hr), and it will send stop report after a preset time (refer the following 120Sec). (min.
[on/off] SEND REPORT IF ADC1 GO DOWN [down voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC1 ENTER/EXIT [min voltage] V TO [max voltage] V for [debounce time] SEC Note: AD1 input voltage range is 0~3.3v, it must connect a resistance to share the voltage if the detected voltage higher than 3.3v,. (4) Speeding report The UNIT will automatically check the current speed information; it will send a report to the server when it is over the defined maximum speed.
2) Base on report mode Parameters: Max. reconnect times, reconnect interval While using this mode, the unit will connect to the server when there is a report to send. If the first connection is failed, it will retry to connect to the server up to the max. reconnect times. Each retry will be separated by the reconnect “interval”. 3) GPRS connect once While using this mode, the unit will connect to the server when there is a report to send (but only try once).
1) Input trigger report All input trigger reports are also configurable. User can customize the events generated by the in-vehicle input to be sent to the server. To enable the particular trigger reports by click the box. 2) Sleep mode (when Duty-Off) (1) TLU100N can go to sleep mode when duty off and TL-sensor is not trigged for 5 minutes. In sleep mode, GPS & GPRS will be disabled.
Note that: 1) Nothing will be changed if no any sensor ever sent ID learning request to the host during ID learn valid period. 2) Every successful “*99*#” command will be valid for only 3 minutes, so user should power on the ID learn need sensor before the state turn into invalid. It will delay 3 minutes for another device ID learning after one time of successful code learning.
3. Question: What are circle geofence and point geofence? Reply: Geofence is just a position check idea. Circle Geofence uses a pre-defined radius and a GPS position center to check a target’s current position and judge whether it is beyond the setting circular scope or not. It may report when a status change detected. The Point Geofence only compare its current GPS coordinate with the predefined one. It may send out a report when it is closing to the checkpoint or away from it. 4.
141 Power of temperature sensor is low 144 Exit defined Circular Geofence area4 (Self Geofence) 145 Enter defined Circular Geofence area4 (Self Geofence) 150 ‘Help’ request 151 User Duty on 152 User Duty off 154 Exit defined Circular Geofence area5 155 Enter defined Circular Geofence area5 156 Door Close (Wireless Door Sensor 1) 157 Door Open (Wireless Door Sensor 1) 158 Door Close (Wireless Door Sensor 2) 159 Door Open (Wireless Door Sensor 2) 160 Door Close (Wireless Door Sensor 3) 161 Door Open (Wireless
284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 Enter point Geofence 4 Enter point Geofence 5 Enter point Geofence 6 Enter point Geofence 7 Enter point Geofence 8 Enter point Geofence 9 Enter point Geofence 10 Enter point Geofence 11 Enter point Geofence 12 Enter point Geofence 13 Enter point Geofence 14 Enter point Geofence 15 Enter point Geofence 16 Enter point Geofence 17 Enter point Geofence 18 Enter point Geofence 19 GROUP C In-vehicle INPUTS event 259 (in-vehicle control INPUT2/TG+)
535 536 537 539 540 Setup the Self-diagnostic report Setup the fixed distance report Setup Course change report Remote setup server IP and port Setup Low Battery report APPENDIX 2: TLU100N SPECIFICATIONS Physical Parameters Enclosure dimensions L*W*H=480*344*46(mm) Weight 7.8kg Battery parameters Capacity Charging mode Ext power supply charge full time (solar panel not work) Solar panel charge full time (no Ext power supply and TLU100N is sleeping all the time) Normal work time (no charging) 7.
Warm Start: Cold Start: Antenna Type <38 sec. (50%), <45 sec. (90%) <90 sec. (50%), <170 sec. (90%) Built-in IO Connection 1* three pin connector 1* 5 wires 1*button PC_SETUP cable Vehicle battery, TG+ input & Door Trigger input RESET Communication GPRS \SMS\RS232 Environmental Operating Temperature Storage Temperature -20°C to +55°C -40°C to +85°C Optional Accessories 1. Built-in GPRS Antenna 900&1800&1900 and 850&1800&1900 models 2. Built-in GPS Active Antenna 3. Wireless door magnetic monitor 4.
+24V TO VEHICLE GND POSITIVE TRIGGER NEGATIVE TRIGGER AD1 RED BLACK YELLOW BROWN WHITE 19 In Commercial Confidence
VI. Federal Communications Commission (FCC) Statement 1) You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 2) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
