GPS&GPRS CAR ALARM GV8300 INSTALLATION MANUAL 1
REV: 1.6 (Series, GV8300V1.20, GV8300-C2) Connectors detail description H1 2*11 connector H1/1&H1/12: The other terminal of the two wires is a 2PIN connector; it is very convenience to connect the solar battery board. The solar battery board is optional; it means that if there is no solar battery board to connect, GV8300 can still work.
H1/6 Purple wire –––300mA optional trunk output – This feature allows you to remote control trunk release. Because the output current is maximum 300mA,it is necessary to connect a relay in order to amplify the drive current. H1/7&H1/18 Green wire –––Cut relay COM The two wires connect to the cutter relay COM contract; the two wires have already been connected together on PCB. The reason that uses two wires is to increase the current of cutter relay.
1N5401 Orange Parking Light 1N5401 H1-20 Brown/Green Wire--- Unlock NO H1/9,H1/10,H1/11,H1/20,H1/21,H1/22 connect to the central door locking. See the drawing below. H1-21 Orange/green wire…Unlock NC H1/9,H1/10,H1/11,H1/20,H1/21,H1/22 connect to the central door locking. See the drawing below. H1-22 Green/White Wire …Unlock COM H1/9,H1/10,H1/11,H1/20,H1/21,H1/22 connect to the central door locking. See the drawing below.
(3) FOR VEHICLES WITH POSITIVE UNLOCKING AND NEGATIVE LOCK SIGNAL (REF DRAWING BELOW) NOTE : WHEN THE VEHICLE IS WITH NEGATIVE, UNLOCK AND POSITIVE LOCK SWITCH BROWN/BLUE TO +12V AND BROWN/GREEN TO GROUND VEHICLE CL CONTROL BOX CUT ACTUATOR CONTROL SWITCH NO UNLOCK COM NC BROWN/BLUE GND BLUE/WHITE ORANGE/BLUE BROWN/GREEN +12V GREEN/WHITE ORANGE/GREEN UNLOCK NO LOCK COM NC (4) FOR VEHICLE WITH DIRECT SWITCHING CENTRAL LOCKING DRIVER SIDE +12V NO LOCK COM NC NO UNLOCK COM NC BROWN/BLUE BLUE/WHITE ORAN
H4 LED+VALET switch port: black 3-pin connector. (Be used in GV8300; GT8000N; GT8005N; GT8010N) Led & Valet Switch H5 PC setup port: white 4-pin connector. H6 MICROPHONE (be used in GV8100N; GV8200N; GV8300) H7 Hs100 port: blue 4-pin connector. (optional) H8 Hand free (be used in GV8100N; GV8200N; GV8300) H9 Shock sensor or Ultrasonic sensor port: white 3-pin connector. (Be used in GT8010N; optional) Shock Sensor H10 RF antenna (be used in GT8010N) H11 Temperature sensor port: blue 3-pin connector.
(1) FOR VEHICLES WITHOUT DRIVER SIDE LOCKING MOTOR +12V UNLOCK BROWN/BLUE BLUE/WHITE ORANGE/BLUE BROWN/GREEN GREEN/WHITE ORANGE/GREEN VAE:3602 ACTUATOR LOCK NO COM NC NO COM NC BLUE GREEN (2) FOR VEHICLES WITH NEGATIVE CENTRAL LOCKING (REF DRAWING BELOW) NOTE : WHEN THE VEHICLE IS WITH POSITIVE CENTRAL LOCKING, CONNECT BROWN/BLUE AND BROWN/GREEN WIRES TO +12V VEHICLE CL CONTROL BOX UNLOCK BROWN/BLUE BLUE/WHITE ORANGE/BLUE BROWN/GREEN GREEN/WHITE ORANGE/GREEN LOCK UNLOCK NO COM NC NO COM NC COM
Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
