GPS&GPRS PERSONAL TRACKING GT2000 OPERATION MANUAL
REV: 2.3 (Standard, GT2000V3.1, GT2000-D2) I. BRIEF INTRODUCTION Personal Tracking System utilizes the GPS and GPRS functions in one unit. You can monitor the vehicle or the people location and set the system remotely. In addition, the unit will send event report if any trigger occurs.
Call Monitoring: user can send a SMS that included the preset password of the unit. GT-2000 will send “PASS” SMS ACK back, unit will auto answer the phone in the following 5 minutes. Using built-in real time clock to identify the report time, when GPS signal is lost. Hence, if the report is received with “LAST KNOWN” message, the time in the report will be the real time clock, but the GPS position will be the last known valid GPS position.
III. PANEL INSTALLATION Battery charger PC-setup IV. BUTTON OPERATION: Button Indication Functions Conditions Press power switch button once Power LED flash 1time/3sec. Power ON Power off Low power Power LED normal is green ，if low power then change to red Press power switch button for 3sec. Power LED off Power OFF If charging then power LED is red, if charge ok then power LED change to green. Power on Charging Press button1 once Power LED change to orange Answer the coming call.
Press button1 for Power LED flash quickly 3 times 2sec. then restore normal Press button2 once Power LED restore normal Send SOS report No incoming call is received Hang up the call. When a call come or in communication or Dialing out Press button2 for Power LED flash 2 times orange Send SOS report and into No incoming call is 2sec. and 1 time green（if low power monitor mold. received no in monitor mold then red） every 3sec.
V. PC SETUP AND SYSTEM INITIATION PC setup Procedure: 1.) Connect the standard RS232 cable to the DB9 port. 2.) Open the PC setup program. 3.) Select the correct COM port for communication. 4.) Power on the device. 5.) Click “OK” to Start the program Note that, if the connection fails, please check the cable connection is secured correctly. A. LOGIN dialog window Connect UNIT DB9 port to the PC serial port with a standard serial cable. Select the COM port, and click “OK”.
C. MAIN INTERFACE 1.[User detail]: If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. Set UNIT ID and UNIT password of for the device. Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters. TCP/UDP address and Port number of alarm center being set, UNIT will send message to these address. Note that either TCP or UDP should be selected.
Set the primary SMS Number of the server. The unit will send reports to the server if GPRS connection is failed. Setup the max. number of the SMS can be sent out from the unit every month. By default, it will be renewed by the first date of every month. “Initialize ” button: clear all data in UNIT. Request All: read out the whole existing setting from GT8000/GT8500. Request: read out the setting in the current page. Apply: transfer the setting to GT8000/GT8500 in the current pages.
Here is the section to set the 3 telephone numbers for speed dialing. Please refer to speed dialing button operation. 3.[Report]: Report setup can be configured in this section. To activate the function(s), please select “√” in checkbox and fill in data in the textbox. There are 2 modes for the GT-2000, first is the Normal mode, and second is the Power saving mode. In the normal mode, the GPS will be always activated if GT-2000 is in moving state.
Emergency request report: If the user does not set the keep alive, GT-2000 might lose the GPRS connection (if it is been cut by the Network). The system will not actively re-connect to server, it will wait for a new trigger (or report) and then start the connection / then send to the server. Special command for SMS mode: If the GT-2000 is not in the GPRS online status, user can send command &&Y02 or &&Y04 to ask unit to connect to server.
To determine whether GT-2000 is moving or not, user can select the sensitivity of the “acceleration sensor”. It is distinguished by the tilt angle of the device. If the unit tilted more than the degree set here, GT-2000 will be in moving mode. Otherwise, it will be in stop mode. APPENDIX 1 GT2000 SPECIFICATIONS Physical Parameters Enclosure dimensions(mm) Weight 94(L)*60(W)*28.5(H) 100g Electrical DC Supply voltage Recharge voltage 3.6V 4.
IO Connection Four Button One Power button, 3 speed dialing buttons 1 volume adjust button Communication GPRS \SMS\RS232\ Environmental Operating Temperature -20°C to +55°C Storage Temperature -40°C to +85°C Accessories 1. Internal battery 2. PC setup cable Additional: 1. GPS indicator (bottom LED): LED is GREEN when the unit has acquired a valid GPS signal, and it will flash when the unit is searching GPS signal. 2. If dialing out to a number fails, the unit will chirp twice. 3.
6-2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
