GPS&GPRS CONTAINER TRACKING SYSTEM MODEL: CTS-100 SERIES OPERATION / INSTALLATION MANUAL
I. BRIEF INTRODUCTION Container Tracking System utilizes the GPS and GPRS functions in one unit. You can monitor the container or the vehicle location and set the system remotely. In addition, the unit will send event report if any trigger occurs. The standard report sent by the unit includes the information: (1) unit’s ID, (2) status, (3) time, (4) GPS’s latitude and longitude, (5) speed, (6) direction, (7) device’s status, (8) event number, and (9) report configuration parameters.
Three LED indicate the status of the system: Power indicator: When the unit power on, the led will flash 1time/3sec by green. If the power has low status, the LED will change to red. when the battery charge ok then power LED will change to green.
IV.
4
5
CTS-100 Installation guide (Project one: vehicle doors with gasket) 6
CTS-100 Installation guide (Project two: vehicle doors without gasket) 7
V. PC SETUP AND SYSTEM INITIATION PC setup Procedure: 1.) Connect the standard RS232 cable to the DB9 port. 2.) Open the PC setup program. 3.) Select the correct COM port for communication. 4.) Click “OK” to start the program 5.) Power on the device. Note that, if the connection fails, please check the cable connection is secured correctly. Note: Turnover SIM card lid angle as following drawing. A. LOGIN dialog window Connect UNIT DB9 port to the PC serial port with a standard serial cable.
B. Version No. Checking The below interface will last until correct UNIT Version No. is checked. (You should run this program before turn on power of UNIT) C. MAIN INTERFACE 1.
If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. IMEI: Any operate with ‘request or request all’ after GPRS power on, the module series number will display automatically, otherwise it displayed with space. Set UNIT ID and UNIT password of for the device. Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters.
Set the primary SMS Number of the server. The unit will send reports to the server if GPRS connection is failed. Setup the max number of the SMS can be sent out from the unit every month. By default, it will be renewed by the first date of every month. UNIT can save 900 reports (900-1). Click ‘Export’ button can export them with Excel or Text format. “Initialize” button: clear all data in UNIT. Request All: read out the whole existing setting from CTS-100.
2. [Geo-fence]: Setup the circular Geo-fence parameters in this window. The format will be center of the Geo-fence and the related radius.
3. [Report]: Report setup can be configured in this section. To activate the function(s), please select “√” in checkbox and fill in data in the textbox. There are 2 modes for the CTS-100, first is the Normal mode, and second is the Power saving mode. In normal mode, the GPS will be always activated if CTS-100 is in moving state. However, if in Power saving mode, CTS-100 will turn off the GPS power if there is no report to send.
(4) GPS wakeup report: While the device is in stop status, user can let the GPS go to sleep mode for power saving. If select GPS sleep ON, user can setup the wakeup report configuration/ or NO GPS wakeup report. IF select GPS SLEEP OFF, CTS-100 will follow the report sending rule in “When Moving” section. Power saving mode While in Power saving mode, CTS-100 will cut off the GPS power if there is no report to send.
2) Base on report mode Parameters: Max. reconnect times, reconnect interval While using this mode, the unit will connect to the server when there is a report to send. If the first connection is failed, it will retry to connect to the server up to the max. reconnect times. Each retry will be separated by the reconnect “interval”. 3) GPRS connect once While using this mode, the unit will connect to the server when there is a report to send (but only try once).
&&Y04,[connection time],[report interval]: For example: &&Y04,3600,60 When received this command, system will connect to server in the next 3600 seconds, and send one report out every 60 seconds. Low battery report: Low battery warning report (to alert user when the external battery level is low) Parameters: On/Off, and warning battery level for report. For example, 30 to represent 30% lower level report. The system will ignore the parameter with a value ‘0’ to prevent continuous non-stop reporting.
4. [Trigger report setup] The unit has built-in door magnetic sensor and tamper switch, user can select if send report when the door sensor and tamper switch has triggered. 1.door sensor :It will send out event reports when door on or off. 2.Tamper switch: the tamper switch is used to check the box of host, when the box of host is moved over, it will send out a relevant report.
GPS* Channels Frequency Sensitivity Tracking Acquisition (Cold start) Position accuracy (Horizontal) 20 parallel tracking L1-1575 MHz -159 dBm -142 dBm ＜2.5m CEP autonomous ＜2.
FCC FOR CTS-100XT 15.21 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
