Installation Guide

ManualsBrandsPortfolio ManualsWall SconcesWS147BNK

BM18016

ITEM #0760399

MODEL #WS147BNK

Français p. 10

Español p. 19

welcoming • sophisticated • inspiring

allen + roth

is a registered trademark

VANITY LIGHT

For Damp

Location

E232083

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday,

8 a.m. - 5 p.m., EST, Friday.

ATTACH YOUR RECEIPT HERE

Summary of content (9 pages)

PAGE 1
welcoming • sophisticated • inspiring For Damp Location E232083 ITEM #0760399 allen + roth® is a registered trademark of LF, LLC. All Rights Reserved. VANITY LIGHT MODEL #WS147BNK Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PAGE 2
TABLE OF CONTENTS Package Contents ............................................................................................................... 2 Hardware Contents .......................................................................................................................... 3 Safety Information ............................................................................................................... 3 Preparation ...........................................................................
PAGE 3
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Machine Screw Qty. 3 Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.
PAGE 4
SAFETY INFORMATION WARNING • All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits and/or inspections. Risk of fire - most dwellings built before 1985 have supply wire rated for 140°F. Consult a qualified electrician before installation.
PAGE 5
ASSEMBLY INSTRUCTIONS 1. Turn off circuit breakers and wall switch to the fixture supply line leads. 1 DANGER: Failure to disconnect power supply prior to installation may result in serious injury or death. 2. Remove existing fixture and disconnect all electrical wiring. ON ON OFF OFF 2 Outlet Box 3. Remove preassembled socket ring (G) from fixture (A). 3 A Remove glass shade (F) and set aside for later use.
PAGE 6
ASSEMBLY INSTRUCTIONS 4a 4a. Remove two decorative nuts (C) from front of fixture (A) and remove mounting strap (B) from back of fixture (A). A 4b. Attach mounting strap (B) to outlet box (not included) using the existing washers and outlet box screws or the machine screws (BB). Note: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult with a licensed electrician before proceeding.
PAGE 7
ASSEMBLY INSTRUCTIONS 6. Prepare wire by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using wire connector (AA). Connect BLACK wire from fixture (A) to BLACK wire from outlet box using wire connector (AA). Connect BARE/GREEN ground wire from outlet box to BARE wire from fixture (A) using wire connector (AA). 6 BLACK AA A WHITE AA BARE NOTE: Screw wire connectors (AA) on in a clockwise direction.
PAGE 8
ASSEMBLY INSTRUCTIONS 8. Align holes in fixture (A) with screws (D) on mounting strap (B) and push fixture (A) toward wall. Attach fixture (A) to mounting strap (B) using the decorative nuts (C) previously removed (Step 4a, page 6). 8 A Note: Fixture (A) can be installed with the sockets facing either up or down. C D 9. Reinstall glass shade (F) and socket ring (G) previously removed (Step 3, page 5). 9 A G F 10. Install one standard-base bulb (not included). Use a 60-watt max.
PAGE 9
CARE AND MAINTENANCE • Shut off main power supply. Wipe fixture with soft, damp cloth. Use window cleaner to clean glass. Do not use an abrasive cleaner. TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM Bulb will not light. POSSIBLE CAUSE 1. Bulb is burned out. 2. Power is OFF. 3. Faulty connection. CORRECTIVE ACTION 1. Replace bulb. 2. Make sure power supply is ON. 3. Check wiring and all connections. Fuse blows out or circuit breaker trips.