Installation Guide

ManualsBrandsPortfolio ManualsOutdoor Wall LightsEFU1691L-4

1 2 3 4 5 6

Lowes.com/portfolioLowes.com/portfolio

Lowes.com/portfolio

Lowes.com/portfolioLowes.com/portfolio

Portfolio is a registered trademark

Lowes.com/portfolio

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday -

Thursday, 8 a.m. - 5 p.m., EST, Friday.

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

EB1569

Portfolio is a registered trademark of

Français p. 7

Español p. 13

PACKAGE CONTENTS

ITEM #0616291

MODEL #EFU1691L-3

WALL LANTERN

PART DESCRIPTION

Fixture Body

QUANTITY

ShadeB

Finial

Strap

Mounting Plate (preassembled to Fixture Body (A))

Mounting Screw (preassembled to Fixture Body (A))

Washer (preassembled to Strap (E))

Steel Washer (preassembled to Strap (E))

Cap Nut (preassembled to Strap (E))

Fixture Screw (preassembled to Fixture Body (A))

HARDWARE CONTENTS (shown actual size)

Outlet Box Screw

Qty. 2

Wire Connector

Qty. 3

CAUTION

• DO NOT touch the LED model/parts at anytime as this may cause damage to the fixture.

• Connect fixture to supply wires rated for at least 167˚F.

• Use only the supplied LED driver to power fixture.

SAFETY INFORMATION

WARNING

• Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear

gloves when handling the parts.

• Account for small parts and destroy packing material, as these may be hazardous to children

• Use flashlight or alternate light source to light work area during installation.

• Assistance may be required to support fixture during installation.

Please read and understand this entire manual before attempting to assemble, operate or install

the product.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

ASSEMBLY INSTRUCTIONS

Turn off power at circuit breaker or fuse panel.

Remove old fixture. Disconnect wiring.

Strip 3/4 in. of insulation from fixture wire ends. Twist

stripped ends together with pliers (not included), black

to black (power), white to white (neutral). Snip ends.

Wrap the ground wire from the outlet box around the

green screw

preassembled on the mounting plate (I),

and then connect the ground wire from the outlet box

to the ground wire from the fixture.

Helpful hint: If the outlet box doesn’t have a ground

wire, you can attach the ground wire from the fixture

directly to the green screw on the mounting plate (I).

Attach wire connectors (BB) to ends. Tape wire

connectors (BB) and wires together with electrical

tape (not included).

Hardware Used

x 3

Wire Connector

PREPARATION

Before beginning installation of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble,

install or operate the product.

Estimated Assembly Time: 15 - 20 minutes

Helpful Tools (not included): Wire stripper, Level.

Tools Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers,

Wire cutters, Electrical tape, Safety goggles, Step ladder and Silicone caulking.

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

ASSEMBLY INSTRUCTIONS

LED chips will not light.

PROBLEM POSSIBLE CAUSE

1. Power is off.

2. Faulty wire connection.

3. Faulty switch.

Fuse blows or circuit breaker

trips when light is turned on.

Crossed wires or power wire is

grounding out.

Check wire connections.

3. Test or replace switch.

2. Check wiring.

1. Make sure power supply is on.

CORRECTIVE ACTION

TROUBLESHOOTING

WARRANTY

The manufacturer warrants all of its lighting fixtures against defects in materials and workmanship

for three (3) years limited from the date of purchase. lf within this period the product is found to be

defective in material or workmanship, the product must be returned, with a copy of the original

sales receipt as proof of purchase, in the original carton, to the place of purchase. The

manufacturer will, at its option, repair, replace or refund the original purchase price to the

consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental

damage, improper handling and/or installation and specifically excludes liability for direct,

incidental or consequential damages. As some states do not allow exclusions or limitations on an

implied warranty, the above exclusions and limitations may not apply to you. This warranty gives

you specific legal rights. You may have other rights that vary from state to state.

CARE AND MAINTENANCE

• Shut off main power before cleaning light with damp cloth or window cleaner.

Do not use abrasive cleansers.

• Bulb Information: 12-watt integrated LED included; do not attempt to replace the LEDs.

Printed in China

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m.,

EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

PART DESCRIPTION PART #

Mounting Plate

0616291-C

0616291-F

0616291-G

0616291-H

0616291-I

0616291-BB

0616291-AA

0616291-J

Cap Nut

Mounting Screw

Washer

Steel Washer

Wire Connector

Outlet Box Screw

Fixture Screw

7. Use silicone caulk (not included) to seal between

wall plate and wall as well as the area around

mounting screws (J).

CAUTION: Leave bottom unsealed so moisture can

drain out.

6. Place fixture body (A) over mounting plate (I),

securing with previously removed mounting

screws (J).

Unscrew cap nut (H) and remove steel washer (G)

and washer (F) from strap (E).

Attach one end of the strap (E) to the nipple of fixture

body (A), securing with finial (D). Attach the other

end of strap (E) to the canopy of fixture body (A).

Re-attach washer (F) and steel washer (G) to stem

on strap (E), securing with cap nut (H).

3. Unscrew fixture screws (C) from fixture body (A).

Attach the shade (B) to fixture body (A) using

fixture screws (C).

Unscrew the mounting screws (J) from fixture body

(A). Save for later use.

Separate the mounting plate (I) from wall plate of

fixture body (A). Then, attach the mounting plate (I) to

outlet box (not included) using outlet box screws (AA).

x 2Outlet Box Screw

Hardware Used

CONSIGNES DE SÉCURITÉ

INSTRUCTIONS POUR L'ASSEMBLAGE