Installation Guide

ManualsBrandsPortfolio ManualsSwag Light Kits32L

ITEM #0075297

0256494

0387262

MODEL #978L

32L

LPSK6BRZ

Français p. 8

Español p. 15

Portfolio® is a registered trademark

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our

customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday -

Thursday, 8 a.m. - 5 p.m., EST, Friday.

Lowes.com/

ortfolio

EB15469

SWAG LIGHT KIT

E127313

Summary of content (7 pages)

PAGE 1
ITEM #0075297 0256494 0387262 Portfolio® is a registered trademark of LF, LLC. All Rights Reserved. SWAG LIGHT KIT MODEL #978L 32L LPSK6BRZ Français p. 8 Español p. 15 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date E127313 Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday Thursday, 8 a.m. - 5 p.m., EST, Friday. EB15469 Lowes.
PAGE 2
PACKAGE CONTENTS PART A B C D DESCRIPTION QUANTITY Chain Hook Wire Cord Switch B A 1 2 1 1 D C HARDWARE CONTENTS (shown actual size) AA BB CC Toggle Nut Qty. 2 Wood Screw Qty. 2 Drywall Screw Qty. 2 Lowes.
PAGE 3
SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. Please read and understand this entire manual before attempting to install the product. DANGER • DO NOT connect this accessory to an electrical system that does not provide a means for equipment grounding. Never use a accessory in a two-wire system that is not grounded.
PAGE 4
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 30 minutes Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire Cutters, Safety Glasses, Stepladder, Drill, 1/2 in. Drill Bit, Pliers Helpful Tools (not included): Soft Cloth ASSEMBLY INSTRUCTIONS 1.
PAGE 5
ASSEMBLY INSTRUCTIONS 3. For drywall installation: Screw the drywall screw (AA) completely into the hook (B). Partially screw the toggle nut (G) onto the drywall screw (AA), turning toggle nut (G) so ends of toggle nut (G) close against drywall screw (AA). Then insert toggle nut (G) into pre-drilled hole in the ceiling. Turn hook (B) until the base of the hook is flush against the ceiling. Skip to Step 5. 3 G AA Hardware Used AA Drywall Screw x2 4.
PAGE 6
ASSEMBLY INSTRUCTIONS 6. Remove preassembled nut on cord switch (D) by turning preassembled screw on opposite side counterclockwise. Gently pull on cord switch (D) to separate. Decide where to locate cord switch (D) on wire (C) and then separate the two conductors of the wire (C) by making a 5/8 in. slit between the two conductors. 6 D nut C 5/8 in. slit 7. Take the non-ribbed conductor of the wire (C) and cut at the center of the slit with wire cutters (not included). 7 C 8.
PAGE 7
ASSEMBLY INSTRUCTIONS 9. Place the halves of the cord switch (D) together again, squeezing gently until they touch. Replace nut on cord switch (D) and tighten screw securely. 9 D D nut 10. Connect wire (C) to a compatible light (sold separately) per the manufacturer’s instructions. Then plug power cord on wire (C) into a wall outlet. NOTE: Use cord switch (D) to turn light fixture ON/OFF. 10 C C D light fixture (sold separately) CARE AND MAINTENANCE • Shut off main power supply.