Installation Guide
ASSEMBLY INSTRUCTIONS/INSTRUCCIONES
DE
ENSAMBLAJE
1.
To
activate the battery (G),
remove the top cover (A) from
the housing
(C)
by twisting
it
counterclockwise. Then,
remove pull tab from the
bottom
of
top cover (A).
Use the switch to choose the
preferred working mode
of
the fixture.
Note:
6H
provides a higher
light output for up to 6 hours
while 1
OH
provides lower light output for up to 10 hours.
Para activar
Ia
baterfa (G), retire
Ia
tapa superior (A) de
Ia
carcasa
(C)
girandola
en
direcci6n contraria a las
manecillas del reloj. Luego, retirez
Ia
languette situee sous
le
couvercle (A). Reglez l'interrupteur
du
luminaire
au
mode
d'eclairage souhaite.
Nota:
6H
brinda una mayor salida de luz por hasta 6
horas, mientras que 1
OH
brinda una menor salida de luz
por hasta 1 0 horas.
2.
Re-attach top cover (A) to
housing
(C)
by aligning the twist
lock numbers
"1"
on
each and
twisting clockwise.
Vuelva a colocar
Ia
tapa superior
(A)
en
Ia
carcasa (C); para ello,
alinee los numeros
"1"
del seguro
por giro y gire
en
direcci6n de las
manecillas del reloj.
3a.
To
install
the
fixture
as a
path light, attach housing
(C)
and stake (E) into post
(D). Then, push the assembly
firmly into the ground.
CAUTION: DO NOT use a
hammer. For ground with
hard soil, use a trowel (not
included) to loosen soil to
prevent breaking the stake
(E).
Para
instalar
Ia lampara
como
una
luz para
sendero,
fije
Ia
carcasa
(C)
y
Ia
estaca (E)
al
poste(D). Luego,
empuje
el
conjunto con firmeza para enterrarlo.
PRECAUCION: NO use
un
martillo. Para suelos con
tierra dura, use una IIana
(nose
incluye) para aflojar
Ia
tierra y evitar romper
Ia
estaca (E).
3b.
To
install
the
fixture
as a
deck/post
light, mount
adapter
(F)
to the desired
installation site with screws
(AA). Then, push housing
(C)
into adapter (F).
Para
instalar
Ia lampara
como
una
luz para terraza
o poste, monte
el
adaptador
(F)
con tornillos (AA)
al
sitio
donde desea instalarla.
Luego, empuje
Ia
carcasa
(C)
en
el
adaptador (F).
--~------------~
REPLACING BATTERY/REEMPLAZO
DE
LAS BATERiAS
1.
Twist and remove the
top cover
(A)
from housing
(C).
Gire y retire
Ia
cubierta
superior (A) de
Ia
carcasa
(C).
2.
Remove battery cover (B) from top cover (A), then remove
battery (G). Replace battery with a new 3.2-volt, 14430
LiFeP04 battery. Replace battery cover (B), then re-attach
top cover
(A)
on
housing
(C)
as
detailed
in
Step 2 above.
FOR FIRST TIME USE: Allow the light to
run
8-12 charging
and discharging cycles to reach battery's maximum
capacity.
3
Retire
Ia
cubierta de
Ia
baterfa
(B) de
Ia
cubierta superior (A)
y luego retire
Ia
baterfa (G).
Reemplace
Ia
baterfa por una
baterfa 14430 LiFeP04 de
3,2 voltios nueva. Vuelva a
colocar
Ia
tapa de las baterfas
(B) y luego vuelva a colocar
Ia
tapa superior
(A)
en
Ia
carcasa
(C)
como se indic6
anteriormente
en
el
paso
2.
EN
EL
PRIMER USO: Deje
que
Ia
luz complete
al
menos
8 a 12 ciclos de carga y
descarga completas para que
se alcance
Ia
capacidad
maxima de las baterfas.
Lowes.com/portfolio