Installation Guide
ASSEMBLY INSTRUCTIONS/INSTRUCCIONES DE ENSAMBLAJE
1.
Attach posts
(D)
to primary light
head (A), secondary light heads
(B) and standard light heads
(C)
by
twisting the posts
(D)
clockwise until
secure. Then attach the posts
(D)
to
stakes
(F)
by twisting the stakes (F)
clockwise.
Fije los pastes
(D)
al
cabezal de
Ia
luz principal (A),
al
cabezal de
Ia
luz secundaria (B) y
al
cabezal
de
Ia
luz estandar girandolos
en
direccion de las manecillas del reloj
hasta que queden firmes. Luego,
fije los pastes
(D)
a las estacas
(F)
girando las estacas
(F)
en
direccion
de las manecillas del reloj.
3.
Install figures into the ground as desired.
2.
Connect the cable
(G)
to the
terminals
on
the bottom
of
the
transformer (H).
Note: DO NOT plug the
transformer into the outlet until
all the light connections are
complete.
Conecte
el
cable
(G)
a las
terminales de
Ia
parte inferior del
transformador (H).
Nota: NO enchufe
el
transformador
al
tomacorriente
hasta que
se
hayan realizado
todas las conexiones de las
luces.
~~'"'''
Terminales
Note:
To
utilize the Bluetooth® functionality, the figure
with primary light head
(A)
should
be
placed
in
the 3rd or
4th spot (for line configurations) or the most center spot
(for scattered installations).
Secondary Secondary Primary Secondary
Light Light
Ll~ht
Light Standard Standard
Lampara Lampara Lampara Lampara Light Light
CAUTION: DO NOT use a hammer to install stakes into
ground. For ground with hard soil, use a trowel (not
included) to loosen the soil to prevent breaking the stake.
CAUTION: DO NOT push
on
the light heads when
installing the fixtures.Hold post near stake and push down
with hand(s).
lnstale las figuras
en
el
suelo segun
lo
desee.
Nota: A
fin
de utilizar
Ia
funcionalidad de Bluetooth®,
Ia
figura con
el
cabezal de
Ia
luz principal
(A)
debe colocarse
en
el
tercer o cuarto Iugar
(en
el
caso de configuraciones
secundaria secundaria
pnnc1pal
secundaria
Luz
estandar
Luz
estandar
en
linea) o
en
Ia
posicion mas central
(en
el
caso de instalaciones esparcidas).
PRECAUCION: NO utilice
un
martillo para instalar las estacas
en
el
suelo.
En
el
caso de suelos con
tierra dura, use una IIana
(nose
incluye) para aflojar
Ia
tierra y evitar que se rompa
Ia
estaca.
PRECAUCION: NO ejerza presion sobre los cabezales de las luces cuando instale las lamparas.
Acerque
el
poste a
Ia
estaca y ejerza presion con las manos.
4.
Once the desired installation layout
is
chosen,
connect the cable
(G)
attached to transformer
(H)
to
each connector (E) preassembled to the path lights.
Note: Make sure the cable
(G)
is
standing upright
in
the
connector (E).
Una vez elegido
el
disef\o de instalacion deseado,
conecte
el
cable
(G)
fijado
al
transformador
(H)
a
cada conector (E) preensamblado
en
las luces para
senderos.
Nota: Asegurese de que
el
cable
(G)
este
en
posicion
vertical
en
cada conector (E).
·-
4
'
-:\
(
..
I
\~
I
•
Lowes.com/portfolio