Installation Guide

ManualsBrandsPorter-Cable ManualsKitchenPneumatic 3/8 in. Upholstery Stapler

UPHOLSTERY

STAPLER

Instruction

manual

The Model and Serial No. plate is located on the main

housing of the tool. Record these numbers in the

sp aces below and ret ain for future reference.

Model No. __________________________________

Type _______________________________________

Serial No. ___________________________________

IMPORTANT

Please make certain that the person who is

to use this equipment carefully reads and

underst ands these instructions before

st arting operations.

Part No. 894666-003

ESPA OL: P`GINA 11

FRAN˙AISE : PAGE 21

MODEL US58

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Summary of content (10 pages)

PAGE 1
E S PA OL: P`GINA 11 FRAN˙AISE : PAGE 21 Instruction manual UPHOLSTERY STAPLER M O D E L US58 To learn more about Porter-Cable visit our website at: http://www.porter-cable.com IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS W ARNING: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed.
PAGE 3
8. DISCONNECT TO O L FROM AIR S U P P LY H O S E before doing tool maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Fig. 5. 9. NEVER USE A TO O L that is leaking air, has missing or damaged parts, or requires repair. Make sure all screws and caps are securely tightened. Fig. 5 Fig. 6 10. DO NOT USE TO O L WITHOUT SAFETY W ARNING LABEL.
PAGE 4
16. DON T OVERREACH. Keep proper footing and balance at all times when using or handling the tool. Fig. 10. Fig. 10 17. FIRE FASTENERS INTO WORK SURFACE ONLY:never into materials too hard to penetrate. Fig. 11. Fig. 11 18. DO NOT DRIVE FASTENERS on top of other fasteners, or with the tool at too steep an angle: the fasteners can ricochet causing personal injury. 19. DO NOT DRIVE FASTENERS CLOSE to the edge of the workpiece.
PAGE 5
O P E R ATING INSTRUCTIONS FOREWORD Porter-Cable Model US58 is a pneumatic upholstery stapler. It is designed to install 3… 8" crown, 22 gauge, wire staples of various lengths (1… 4"to 5… 8" long, see ACCESSORIES Listing in back of this manual). POWER SOURCE This tool is designed to operate on clean, dry, compressed air at regulated pressures between 60 and 100 PSI (Pounds per Square Inch).
PAGE 6
Fig. 17 Fig. 16 P R E PARING THE TO O L 1. After reading and understanding this entire manual, connect tool to air supply. CAUTION: Keep tool pointed away from yourself and others at all times. Always connect tool to air supply before loading fasteners. Do not load fasteners with trigger depressed. Only use approved fasteners (see ACCESSORIES). Always wear Z87 approved safety glasses, and hearing protection when preparing or operating the tool. Never use a tool that leaks air or needs repair. 2.
PAGE 7
The depth that a fastener is driven is controlled by the pressure of the air supply.The amount of pressure required will vary depending on the size of the fastener being used and the material being fastened. Experiment with the air pressure setting to determine the best pressure for the job at hand. Use only enough pressure to drive the fastener heads on top of the workpiece (not into the workpiece). Air pressure in excess of that required will cause premature wear and/or damage to the tool.
PAGE 8
TROUBLESHOOTING CAUTION: Disconnect tool from air supply before performing any Service Procedure. SYMPTOM 1. Air leak near top of tool or in trigger area. PROBLEMS Loose screws. Worn or damaged o-rings or seals. SOLUTIONS Tighten screws. Install OVERHAUL Maintenance Kit. 2. Tool does nothing or operates sluggishly. Inadequate air supply. Inadequate lubrication. Worn or damaged o-rings or seals. Verify adequate air supply. Put 1 or 2 drops of oil into air inlet. Install DRIVER Maintenance Kit. 3.
PAGE 9
PORTER-CABLE LIMITED ONE YEAR WA R R A N T Y Porter-Cable warrantsits nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.
PAGE 10
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) (CENTRE DE SERVICE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Power Tools are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) (Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien) ARIZONA Tempe 85282 (Phoenix) 2400 West Southern Avenue Suite 105 Phone: (602) 437-12