LIFESPAN: PATINA 13 FRANCHISE : PAGE 25 FINISH MAILER MODEL DA250B IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. The Mode! and Serial No. plate is located on the rain housing of the tool. Record these numbers in the PORTER: ABLE spaces below and retain for future reference. Model No. SIMPLETON ER es TI Type Serial No. Part No.
SAFETY GUIDELINES / DEFINITIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below, Please read the manual and pay attention to these sections. ELT Te oi ie Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
PLU GENERAL SAFETY RULES 1. Read and understand tool labels and manual, Failure to follow warnings could result in DEATH or SERIOUS INJURY. Fig. 1. 2. Operator and others in work area MUST wear safely glasses with side shields. These safety glasses must conform to ANSI 287.1 requirements {approved glasses have “Z87" printed or stamped on them). Fig. 2. 3. Keep fingers AWAY from trigger when not driving fasteners 1o avoid accidental firing. Never carry tool with finger on trigger.
9. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). 10. All air line components {hoses, connectors, filters, regulators, tee) must be rated for a maximum working pressure of at least 150 PSI (10.3 BAR) or 150% of the maximum system pressure, which ever is greater. 11. Connect teal to air supply hose with a coupling that automatically removes all pressure from the tool when the coupling is disconnected. Fig. 7.
21. Remove finger from trigger when not driving fasteners. Never carry tool with finger on rigger. In “Contact Actuation Mode” tool will fire a fastener if safety is bumped while trigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing and balance at all times when using or handling the tool. Fig. 14 23. Fire fasteners into work surface only: never into materials too hard to penetrate. Fig. 15. Fig. 16 24.
EMPLOYER'S RESPONSIBILITIES Employer must enforce compliance with the safety wakings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper aeration of this tool, read and understand tool labels and manual. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Read and follow all of these instructions carefully.
3. Observe fastener icon {A} Fig. 189A. Insert fasteners (B) Fig. 19A with points down {C) Fig. 19A, Slide fasteners forward to the front of the magazine. The magazine will hold two full strips of fasteners, IMPORTANT: Fasteners must point in the same direction as they will be driven. 4. Feed the strip of fasteners into the magazine ("T" slot), until they are past the spring (A) Fig. 20. 5. Pull the follower {B) Fig. 21, all the way to the rear of the magazine and release.
OPERATING INSTRUCTIONS USING THE TOOL WITH DIFFERENT TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool, This tool is shipped from the factory with a “single sequential actuation” trigger which will limit the tool to firing method number 1 only. A “contact actuation” trigger is available. The “contact actuation” trigger allows the tool to be fired in either of two methods described below; 1.
-— A Fig. 25 Fig. 26 A rubber nose cushion (A) Fig. 25, is provided to reduce marring of the work surface. The rubber cushion can be removed to provide increased depth-of drive for toe-nailing applications. When not in use, a storage Location is provided for the the rubber cushion on the magazine (A Fig. 26. CRITICIZER Disconnect tool from air supply before removing or re-installing rubber cushion. CLEARING A JAMMED FASTENER YULETIDE Disconnect tool from air supply. 1.
LT CLEAN AND INSPECT DAILY EIS disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of fool only if necessary, DO NOT SOAK tool with cleaning solutions. Such solutions can damage internal parts. Inspect trigger and safety mechanism to assure system is complete and functional: no loose or missing parts, no binding or sticking parts.
TROUBLESHOOTING FRI MINNIE Disconnect tool from alr supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Airlessness of Loose screws, Tighten screws. tool or In rigger area. Worn or marriage Install Overhaul Kit o-ring or seals. 2. Coal toes nothing or adequate air supply. Verity adequate air Apply. operates piggishly.
