Installation Manual

ManualsBrandsPop & Lock ManualsCarPL9772

PL9555 (and PL9772)

Power Lock

Installation Instructions

www.popandlock.net

(800) 342-5911

1) Locate and remove the Emergency

Release Handle with Phillips screw.

Cover Screws

Cover

E-Clip

Cap and

Tonneau

Harness

Lock Module

Wire Taps

Cable Clamps

Clamp Screws

Cable Ties

Truck Harness

2) Locate and remove the black

plastic Dust Cover if one is

installed. May need to cut it

off if necessary.

Remove plastic dust cover and also emergency release

handle before installing Lock Module.

Be sure Lock Module is in the

UNLOCK position before

installing it onto the handle.

Mounting Tap must be at

the bottom when installing

on the Handle.

3) Install the Lock Module by

sliding it over the handle, be

sure the mounting tab is at

the bottom and lines up with

the notch in the handle when

sliding it on.

Summary of content (7 pages)

PAGE 1
Cover www.popandlock.net (800) 342-5911 Truck Harness Cover Screws Lock Module PL9555 (and PL9772) Power Lock Installation Instructions Clamp Screws Cable Clamps Wire Taps Cap and Tonneau Harness E-Clip Cable Ties 1) Locate and remove the Emergency Release Handle with Phillips screw. 2) Locate and remove the black plastic Dust Cover if one is installed. May need to cut it off if necessary. Remove plastic dust cover and also emergency release handle before installing Lock Module.
PAGE 2
Handle is notched to except tab on Lock Module Install E-Clip into groove in handle 4) Install the Stainless Steel Eclip into the groove in the handle to hold the Lock Module in place. 5) Reinstall the Emergency Handle and cables to the rotary latch, route the passenger side cable through the cable guide hole on the Lock Module the out to the rotary latch. Reinstall passenger side cable by routing it through the guide hole in the Lock Module then out to the rotary latch.
PAGE 3
6) Install the Cap and Tonneau Harness; insert the red female spade ends of the harness into the Lock Module with the red wire on top. 7) For Cap installations fasten the Cap Harness to the rear door glass using supplied adhesive backed foam tubes installed on the harness. Be sure that the glass is clean and dry then remove the adhesive backing and stick it to the glass.
PAGE 4
9) Install the Truck Harness by removing the driver’s side tail light then running the non fused end of the harness up under the bed rail, through the back of the tail light compartment, down to the truck frame following the factory wiring harness to the front of the truck. Run the harness up from the frame, through the firewall and into the driver’s side kick panel. Fasten the harness to the truck securely using the supplied Cable Ties as needed.
PAGE 5
VEHICLE WIRING CHART Pop N Lock/ Load N Lock (All wire color information is for reference only and may vary by vehicle) Please verify with a test light If you have trouble locating the lock and unlock wires, test all the wires with a test light that are inside the rubber boot that runs between the door and the cab of the truck to find correct wire colors.
PAGE 6
VEHICLE WIRING CHART Pop N Lock/ Load N Lock (All wire color information is for reference only and may vary by vehicle) Please verify with a test light If you have trouble locating the lock and unlock wires, test all the wires with a test light that are inside the rubber boot that runs between the door and the cab of the truck to find correct wire colors.
PAGE 7
LIMITED WARRANTY TERMS AND CONDITIONS (1) Installation. Pop & Lock™, LLC (and Pop & Lock™ Corporation) is not responsible for installing the Pop & Lock™ or for the harm suffered by any person as a result installing it. (2) Warranties. a. Customer acknowledges that it is unreasonable to believe that any device whatever will prevent a theft in the case of every attempt and that the most that can be expected from a so-called anti-theft or security device is that it will deter many thieves. b. POP & LOCK™ LLC.