MR45 OWNER’S MANUAL CD/MP3/WMA Player Sirius Ready (for MR45S and MR45D only) AM/FM Stereo Radio Supports DMD (DMD - Digital Music Device (for MR45S and MR45C only) like iPod®, MP3 or Smartphone devices) Play USB Music Front and Back AUX-In Flip Down Front Panel System (for MR45S and MR45C only)
TAB L E O F C O N T EN T S Installation………………………………………………………………………..3 Wiring Diagram…………………………………………………………………..5 Button Description………………………………………………………………7 Basic Operation………………………………………………………………….8 Radio Operation…………………………………………………………………9 Sirius Operation………………………………………………………………..10 CD/MP3/WMA Operation……………………………………………………...12 iPod ® Operation……………………………………………………………….15 Auxiliary Operation……………………………………………………………16 USB Operation………………………………………………………………….16 Optional Accessories………………………………………………………….
I N S T A L L AT I O N IMPORTANT! Before mounting be sure there is sufficient room to accommodate the unit and that there is sufficient ventilation. Before installing the unit, connect the wiring temporarily making sure the system works properly. Only use the parts included with the unit to ensure proper installation. Receiver should be mounted within 30º (+ or— 15º) from Horizontal. If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance.
St e p 2 ) 54mm St e p 3 ) St e p 4 ) 4
S t e p 5 ) To s u p p o r t t h e u n i t hex nut M5 mounting surface plain washer lock washer plain washer mounting sleeve mounting surface unit rear support strap tapping screw WIRING DIAGRAM (optional) (reserved) 5
Wiring Details: Use the wired plug end (Pigtail) provided to make power and speaker connections according to the diagram below. Using this connector will make it easy to disconnect the radio for adding additional features or service. Removing the factory plug end will void warranty.
Blue Wire - This wire outputs a 12V signal when the MR45 turns on. It is used to remotely turn on external amplifiers. Notes: Use the included plug/wire bundle to connect to the power source and speakers. The Yellow, Red and Black power wires should be 14AWG or larger depending on the length to the battery. NEVER operate the unit without the proper power and ground wire. NEVER ground the speaker leads and NEVER allow the speaker leads to come in contact with each other.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20.
ZONE/STEREO/MONO/P-VOL FUNCTION Press and hold SEL button for 5 seconds to enter menu select function then press + or - button to adjust desired setting. Press SEL button again to select different functions. Unit will return to normal previous display if left untouched for 5 seconds. SEL ZONE SEL STEREO/MONO SEL P-VOL ZONE: AMERICA/EURO/CHINA frequency switch. STEREO/MONO mode P-VOL: Adjust Initial Volume level using this mode. SETTING THE CLOCK 1. Press DISP button to display the clock 2.
SELECTING A STATION Press / button to select a station. hold or button. To use manual tuning, press and AUTOMATIC MEMORY STORING & PRESET SCAN (A/PS) The PRESET buttons can be used to store 6 stations in each band (FM 1, FM 2, FM 3 and AM1, AM2) for convenient access to your favorite stations.
Press MODE button to change to SIRIUS mode. If there is no SIRIUS TUNER connected this mode will be skipped. Please connect your SIRIUS Tuner to the SIRIUS port located at the back of the unit. Then press MODE button to change to SIRIUS mode. SELECTING A CHANNEL Press / button to select a channel. SEARCHING CHANNEL NUMBER MANNUALLY Press A/PS button ―SR CH - - - ‖ will show on the display. Use the PRESET 1, 2 and 3 buttons to select the desired channel number.
3. Repeat steps 1 and 2 to program additional channels. PARENTAL CONTROL You can lock any Sirius channels you do not want others to have access without your permission. The default code is "5220". In case you forget your code please disconnect the unit completely from the power. - GUIDE ON HOW TO ENTER THE CODE USING THE PRESET BUTTONS Press preset 1INT button five times to enter 5, press preset 2RDM button two times to enter 2 and press preset 3RPT button twice to enter 2.
up. The CD will be drawn inside and will play automatically once inserted. If a CD is already inserted in the driver: Press MODE button to change to CD mode. SELECTING SONGS Press or button to select a song. button to fast forward or rewind a song. Press and Hold or SELECTING SONGS BY FOLDER Note: Make sure RPT MODE is off before using this function Press 5 button or 6 button to select directory downward or upward. If a directory does not exist or does not have music files, it will be skipped.
resume play. EJECTING A DISC To remove a disc, open the disc cover and press from the driver and close disc cover. button. Remove CD DISC NOTES A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, heart) may damage the unit. Be sure to use round shape CD discs only in this unit. 2. Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction or damage the unit. 3.
I P O D ® O P E R AT I O N SWITCHING TO IPOD® MODE Please Note: You need iPC4580 cable (sold separately) before you can connect your iPod® to this unit. If an iPod® device is already connected: Press MODE button to change to IPOD® mode. If there is no iPod® device connected the display will show ―NO IPOD®‖ Turn on your iPod® device and connect to the iPC4580 Cable then connect this cable to the iPod® port located at the back of the unit. Then press MODE button to change to IPOD® mode.
A U X O P E R AT I O N SWITCHING TO AUX MODE This unit can be connected to any portable devices such as an iPod®, MP3 Players, TV or DVD through the AUX IN jack on the front or at the back of the unit. Press MODE button to change the mode to ―AUX 1‖ (back) or ―AUX 2‖ (front) mode. Please Note: In this mode, all controls and functions has to be controlled from your music device.
COMPATIBLE ACCESSORIES (sold separately) MR45R Wired Remote Control – connect to the back of the unit labeled ―TO MR45R‖. You can add up to 2 MR45R in conjunction with CMR-Y7. MRR21 IR Wireless Remote Control - the IR eye is located next to the volume button and must be in line of site for the remote to operate. MRRF18 RF Wireless Remote Control with Receiver – simply connect the receiver to the IR port located at the back of the unit.
Unit not playing CD CD is extremely dirty or damage CD, laser head is dirty, CD was inserted in reverse direction or the ambient is too high Sound skips when playing CD The installation angle is more than 30 degrees or CD is extremely dirty or damage CD Cannot read some USB devices This unit is not 100% compatible with all USB devices or the USB devices has special format. The battery may be too low (the unit operating voltage is 10.8v to 15.6v). This is normal.
T E C H N I C A L S P E C I F I C AT I O N S CD Player Signal to Noise Ratio Frequency response Channel Separation A/D converter Electronic anti shocking SPECIFICATION >80dB 20Hz-20KHz >65dB 16Bit CD 20S/MP3 60S TUNER(AM) Frequency Range Usable Sensitivity 530-1710 KHz 32 dBuV TUNER(FM) Frequency Range Channel Step Sensitivity Stereo Separation Signal to Noise Ratio 87.5-107.9 MHz 200KHz 8dB 30dB 60dB LINE-OUT Output Impedance 5 Volt ( max ) 33 Ohm GENERAL 13.8V DC (10.8-15.
W A R R A N T Y I N F O R M AT I O N This unit is warranted to be free of defects in material and workmanship for a period of one year. Warranty is subject to proper installation and operation within the published specifications. Except as provided below, Poly-Planar will repair or replace, at its discretion, any unit returned prepaid to our facility with proper documentation and determined to be defective in normal use. Poly-Planar is not liable for any consequential damages.
NOTES: 21
NOTES: 22
