Instructions / Assembly

ManualsBrandsPolygroup ManualsOutdoorsPRO Series 24 ft. Round 52 in. Deep Metal Frame Swimming Pool Package

1 POWER FILTER INSTALLATION: (Reference Page 3, Fig. 1)

WARNING - EXTREMELY IMPORTANT!

4. These Skimmer Filter Systems are manufactured by Polygroup and ETL control number 4000608 -

double insulated and grounded - 115 V.A.C. - 60 Hz. (Unit must have a minimum of 105 V.A.C. to start

and run properly.) The units’ wattage and capacity is as follows:

SFS600 Filter System with F600C Pump 46 watts 0.8 amps 580 G.P.H.

780 G.P.H.

1075 G.P.H.

1500 G.P.H.

2000 G.P.H.

1.1 amps

2.2 amps

57 watts

80 watts

120 watts

210 watts

SFS600 Filter System with F700C Pump

SFS1000 Filter System with F700C Pump

SFS1000 Filter System with F1000C Pump

SFS1000 Filter System with F1500C Pump

SFS2000 Filter System with F2000C Pump

IMPORTANT! Your pump is protected by a thermal overload. This device senses the temperature of the

pump and if it is getting too hot, it will open the electric circuit and the pump will stop running until it cools

off. It will automatically turn back on when it has cooled down. This is a safety device to help prevent exces-

sive pump damage. If your pump is automatically turning off, it is because of high pool water temperature

and/or low water flow through the pump. If this happens you need to check water flow through the filter

and correct it if needed as this pump uses the water flow for cooling. You may also want to run the pump at

night when the temperature is lower.

Should you encounter any problems, contact the Customer Service at (888) 919-0070.

Extended operating days and hours during peak season requirements.

s 2ISK OF ELECTRICAL SHOCK CONNECT ONLY TO A GROUNDING TYPE

receptacle.

s 2ECEPTACLE MUST BE AT LEAST  FEET AWAY FROM POOL

s &ILTER SYSTEM CAN BE USED AS MANY HOURS AS DESIRED

s $O NOT USE AN EXTENSION CORD TO CONNECT UNIT TO ELECTRIC

supply; provide a properly located outlet.

s $O NOT BURY THE CORD

NOTE - The Power Filter will be in four sections: a pump; filter assembly; hardware bag; and return hose.

A. First, Locate the filter assembly, remove the Lock Top (11), Strainer Basket (10), and Filter Cartridge (9) from

the assembled Filter Case. Locate the mounting location for the power filter on the Pool Wall (32). Install one

Gasket (22) over the four alignment pins on the skimmer canister (8) and place it up to the outside pool wall

inserting the four alignment pins through the four large holes in pool wall. Now leaning against the Skim-

mer to hold it in place add the inside gasket (22) over the pins on the inside of the pool wall. Now place the

Face Plate (23) over the alignment pins. Place the Hex Head Screws (24) into the holes. Start all the Hex

Head Screws one and a half turns each. Then proceed in tightening them in equal turns each in sequence

around the Face Plate until all are equally tight and you have a good even seal. Warning! Be sure not to over

tighten them, you just need a water tight seal.

B. Now lubricate the pump O-ring with petroleum jelly (not provided). Hold the Skimmer Canister (8) securely,

and insert motor pump so that the outlet on the volute housing extends out of the opening in the side of

the filter case as shown in Fig. 2. Insert the motor pump until the two ribs on the inlet of the volute housing

protrude through the bottom of the filter case. Reach down inside the canister and place the Pump Retain-

ing Nut (7) over the top of the volute housing inlet as shown in Fig. 2. Twist

the Nut (7) clockwise until it is snug.

C. Locate the Pool Wall Fitting assembly parts (15-21). Lubricate the black

Wall Fitting Gasket (16) with petroleum jelly and install it over the

threads on the Pool Wall Fitting (15). Insert the pool wall fitting with

the gasket through the hole in the wall from the inside of the pool.

Place the Thrust Washer (17) over the pool wall fitting and then

thread the Wall Fitting Nut (18) onto the fitting until it is hand tight.

DO NOT over tighten the wall fitting nut or wrinkle the pool wall

around the Wall Fitting Thrust Washer (17) or Wall Fitting Gasket (16).

Now apply some petroleum jelly to the thread of the Elbow 90° (19)

and install the elbow into the wall fitting assembly. Install the Diverter

Fitting (20) and Locking Ring (21) onto the wall fitting.

D. Get the Return Hose (13) and remove the two Hose Clamps (14) from the hardware bag. Loosen the hose

clamps and slide them over the end of the hose. It is recommended to lubricate the O-Rings (12) on the

Volute Housing and on the Elbow (19) before installing the hose (13). Install the hose on the pump volute

housing and on the Elbow (19). Tighten both of the Hose Clamps (14). See Fig. 3.

E. Place the Filter Cartridge (9) and the Strainer Basket (10) back into the

Skimmer Canister (8). It is important that the Filter Cartridge (9) slips

over the Pump Retaining Nut (7) and seals at the bottom of the canister

so that the Strainer Basket (10) will seat in it’s groove inside the canister.

See Fig. 4. Place the Lock Top (11) on top of the Skimmer Canister (8)

and lock it in place by turning it clockwise until it is locked. Push the

Weir Foam Pad (25) into the Weir (26) and under the tabs, to hold it in

place. Take the Weir (26) and slide it into the grooves from inside the

pool. See Fig. 4. Once the weir is pushed inside the grooves, flip it over

as shown by the Arrow #2 in Fig. 4, to lock it in place. NOTE: The weir

can ONLY be pushed into the grooves as shown by Arrows #1 in Fig. 4,

by holding it horizontal. Be sure the weir moves freely through the

opening, if not carefully trim away any obstructing material to allow the weir to move freely.

F. After the pool is filled, SEE (WATER LEVEL FIG. 4) check the hose connections and fittings to make sure there

is no water leakage. If any leaks are found, see #4 in the Trouble Shooting guide on page #8.

FIG. 4

MIN. WATER

LEVEL

MAX. WATER

LEVEL

FIG.3

!!!!!!!!!32

1"6

NOTE:

When Pump needs servicing or working on Return Hose (13), turn off power and install the Service Plug

(30) into Pool Wall Fitting (15) after removing Locking Ring (21) and Diverter Fitting (20). Also install a

Service Plug (30) into center hole of the Skimmer Canister (8) after removing the Pump Retaining Nut (7).

See FIG. 1. When service is complete remove both Service Plugs (30) reversing the procedures above.

1-6

THE FILTER CARTRIDGE (9) WILL HOLD 1”

DIAMETER CHLORINE TABLETS. CHECK

YOUR CHLORINE LEVELS TO DETERMINE

THE PROPER NUMBER OF TABLETS

TO ADD.

NOTE:

Install Service

Plugs (30)

only when

servicing

system!

KEY DESCRIPTION

1-6 MOTOR PUMP

7 PUMP RETAINING NUT

8 SKIMMER CANISTER

9 FILTER CARTRIDGE

10 STRAINER BASKET

11 LOCK TOP

12 O-RING

13 RETURN HOSE

14 HOSE CLAMP

15 POOL WALL FITTING

16 RUBBER GASKET

17 THRUST WASHER

18 NUT

19 ELBOW 90°

20 DIVERTER FITTING

21 LOCKING RING

22 GASKET

(One Spare Included)

23 FACE PLATE

24 HEX HEAD SCREWS

25 WEIR FOAM

26 WEIR

27 VACUUM ADAPTER

28 DRAIN CAP

29 SEAL GASKET

30 SERVICE PLUG

32 POOL WALL

FIG.1

［

Volute Housing

Pump System Wattage Amperage Flow Rate

*GPH - Gallons Per Hour

PATENTED

FILTER

CARTRIDGE

SYSTEM #7,005,062

FIG.2

Motor Pump

Skimmer

Canister

Volute

Housing

Outlet

Volute

Housing

Inlet

POOL

RETURN

FITTING