User Manual

ManualsBrandsPOLYCOOL ManualsOtherPOLYCOOL Ice Maker

Ice Maker

Making Ice

If ice is made and left in the appliance, it may eventually melt – when melted, the water returns to the

water reservoir. Be careful to avoid overflow from the water reservoir due to melted ice adding to the

current reservoir contents. • Ensure that adequate water is in the water reservoir when making ice. • It takes

several minutes to create each batch of ice cubes, and this is also affected by the ambient temperature – do

not expect instant ice to be available. To monitor ice production, view it through the "window" in the ice / water

reservoir cover – do not allow the cover to remain open, and close it as soon as possible in order to retain

ice-cold temperatures in the ice reservoir. • Note that the size of the ice cubes may vary for the first few ice

making cycles.

Switch the ice making function ON using the START button. When on, the appliance draws water up from the

water reservoir into the cooling unit, creates the ice, drains excess water back into the water reservoir, then

moves the ice into the ice collection tray. Use the supplied scoop to collect the ice.

Care and Maintenance

• After use, drain the appliance by removing the drain cap on the rear of the unit until no water remains.

Re-install drain cap and open reservoir covers approximately halfway and leave open. This helps

thoroughly dry the inside of the appliance and helps prevent corrosion of surfaces.

• After each use, clean the inside of the appliance with a cloth and a solution of water and a small amount of

vinegar. Do not use detergents, solvents or chemicals.

• When the appliance is in use, ensure that the reservoir cover is fully closed.

• Regularly remove any accumulated dust from the air vents and cooling holes in the body of the machine.

• If required, clean the appliance body with a damp cloth. Do not use detergents, solvents or chemicals.

This image shows water in the

ice making tray and ice forming

on the cooling elements. When

the ice cubes are ready, the

remaining water is returned to

the water reservoir, the ice drops

from the cooling elements and is

shifted to the ice reservoir by a

"comb".

YCOOL POL

YCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POL

YCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

YCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL POLYCOOL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL POL

POLYCOOL POLYCOOL POLYCOOL POLYCOOL

POLYCOOL POLYCOOL POLYCOOL

POLYCOOL POLYCOOL

YCOOL POLYCOOL