User's Guide
Table Of Contents
- Contents
- Before You Begin
- Getting Started with Polycom® Pano
- RealPresence Content Pod Power
- Power On the Content Pod System
- Procedure
- 1 Use the HDMI cable to connect the RealPresence Content Pod system to the monitor.
- 2 Connect the touch monitor USB cable.
- 3 Connect the power cord to the RealPresence Content Pod system or connect the LAN cable to power on the system by Power over Ethernet (PoE).
- 4 If it is not already connected, connect the LAN cable to the system for network connectivity.
- Procedure
- Power On Self Test (POST)
- Power Off a RealPresence Content Pod System
- Power On the Content Pod System
- RealPresence Content Pod Home Screen
- RealPresence Content Pod Power
- Share Content
- Note: The RealPresence Content Pod system does not support high-bandwidth digital content protection (HDCP). If you share HDCP-encrypted content, it is not shown.
- Share Your Screen
- Share Your Screen Using Miracast
- Procedure
- 1 Make sure the device is connected to the same Wi-Fi network as the RealPresence Content Pod system.
- 2 On the device, access the Miracast or compatible screen mirroring feature. Miracast is supported on a variety of devices that use different methods for accessing the feature. On most devices, the screen mirroring feature is accessed from the Settin...
- 3 On the device, select the name of the RealPresence Content Pod system shown on the home screen.
- 4 When prompted, enter the PIN shown on the RealPresence Content Pod home screen.
- Procedure
- Share Your Screen Using AirPlay
- Procedure
- 1 Make sure the AirPlay-enabled device is connected to the same Wi-Fi network as the RealPresence Content Pod system.
- 2 Access AirPlay on the device. On most iOS devices, the AirPlay feature is located in the Control Center that you open by swiping up from the bottom of the device. For details, check your device documentation.
- 3 Select the name of the RealPresence Content Pod system that is shown on the home screen.
- 4 When prompted, enter the PIN shown on the RealPresence Content Pod home screen.
- Procedure
- Share Your Screen Using Miracast
- Stop Sharing Your Screen
- Share Content from a Device Connected to RealPresence Content Pod
- Supported HDMI Input Resolutions and Frame Rates
- UHD
- 3840 x 2160p
- 24,25,30
- OHD
- 2560 x 1440p
- 50,60
- FHD
- 2560 x 1440p
- 50,60
- WSXGA+
- 1680 x 1050
- 60
- UXGA
- 1600 x 1200
- 60
- SXGA
- 1280 x 1024
- 60,70,75,85
- HD
- 1280 x 1024
- 50,60
- XGA
- 1280 x 1024
- 60,70,75,85
- Note: The way you set the resolution and refresh rate differs, depending on the type of operating system you have. Check your computer’s manual or help topics for the appropriate steps.
- Procedure
- 1 Connect one end of an HDMI cable to the HDMI Input port on the monitor. Connect the other end of the HDMI cable to the HDMI Output port on the RealPresence Content Pod system.
- 2 If your monitor has only a DVI input port, use a DVI-HDMI adapter to connect it to the HDMI output port of the RealPresence Content Pod system.
- Supported HDMI Input Resolutions and Frame Rates
- Stop Sharing Content from a Connected Device
- Polycom Pano App
- Install RealPresence Content Companion
- Use Content Companion in Standalone Mode
- Share Content Using Polycom Content Companion
- Check Application Information
- Connect to a Room System
- Disconnect from a Room System
- Share Local Content
- Stop Sharing Local Content
- Annotation Toolbar
- Annotation Toolbar Elements
- Annotation Toolbar Elements
- 1
- Expands the view of the whiteboard, blackboard, or content to full screen.
- 2
- Highlights briefly on content to note certain areas of interest.
- 3
- Provides drawing line widths.
- 4
- Provides color selections.
- 5
- Undoes the last annotation.
- 6
- Erases annotations made on whiteboard, blackboard, or content.
- 7
- Captures a snapshot of live content.
- 8
- Provides a blank whiteboard to create annotations.
- 9
- Provides a blank blackboard to create annotations.
- 10
- Exits the current content sharing interaction screen and returns to the Home screen
- Annotation Toolbar Elements
- Annotate Content
- Erase an Annotation
- Undo an Annotation
- Use Snapshot to Annotate Content
- Stop Sharing Annotated Content
- Highlight Content
- Create a Whiteboard or Blackboard
- Exit the Annotation Toolbar
- Annotation Toolbar Elements
- Troubleshooting
Polycom Content Companion
Polycom, Inc. 12
Procedure
» Start Poly
com Pano app and click or tap Skip on the Sign In screen.
Share Content Using Polycom Pano App
After connecting to a room, you can share your local desktop or a running local application on the
Polycom Pano room system.
Check Application Information
The Polycom Pano app version and copyright information are located on the application title bar.
Procedure:
1 Click or tap on the application title bar.
2 Click or tap About.
Connect to a Room System
You must connect to a room system before you can share content.
Automatically Detect Rooms
If your Bluetooth detection is turned on, Polycom Pano app can detect nearby Polycom Pano room
systems that have enabled Bluetooth broadcasting to facilitate content sharing. Detected rooms are listed
on the Connect to window.
Connect to an Automatically Detected Room
After you enable Bluetooth on your device, Polycom Content Companion can automatically detect nearby
rooms. You can then connect to a detected room.
Procedure
1 Click or tap a room listed under Connect to.
2 Enter the room PIN code, if asked.
Recent Devices
Up to five recently connected devices are listed under Recent Devices. You can connect to a recent device,
or remove devices from the Recent Devices list.
Note: The auto discovery feature is available to Microsoft Windows 10 users with Bluetooth version
4.0 or higher.