User's Guide
Table Of Contents
- Contents
- Before You Begin
- Getting Started with Polycom® Pano
- RealPresence Content Pod Power
- Power On the Content Pod System
- Procedure
- 1 Use the HDMI cable to connect the RealPresence Content Pod system to the monitor.
- 2 Connect the touch monitor USB cable.
- 3 Connect the power cord to the RealPresence Content Pod system or connect the LAN cable to power on the system by Power over Ethernet (PoE).
- 4 If it is not already connected, connect the LAN cable to the system for network connectivity.
- Procedure
- Power On Self Test (POST)
- Power Off a RealPresence Content Pod System
- Power On the Content Pod System
- RealPresence Content Pod Home Screen
- RealPresence Content Pod Power
- Share Content
- Note: The RealPresence Content Pod system does not support high-bandwidth digital content protection (HDCP). If you share HDCP-encrypted content, it is not shown.
- Share Your Screen
- Share Your Screen Using Miracast
- Procedure
- 1 Make sure the device is connected to the same Wi-Fi network as the RealPresence Content Pod system.
- 2 On the device, access the Miracast or compatible screen mirroring feature. Miracast is supported on a variety of devices that use different methods for accessing the feature. On most devices, the screen mirroring feature is accessed from the Settin...
- 3 On the device, select the name of the RealPresence Content Pod system shown on the home screen.
- 4 When prompted, enter the PIN shown on the RealPresence Content Pod home screen.
- Procedure
- Share Your Screen Using AirPlay
- Procedure
- 1 Make sure the AirPlay-enabled device is connected to the same Wi-Fi network as the RealPresence Content Pod system.
- 2 Access AirPlay on the device. On most iOS devices, the AirPlay feature is located in the Control Center that you open by swiping up from the bottom of the device. For details, check your device documentation.
- 3 Select the name of the RealPresence Content Pod system that is shown on the home screen.
- 4 When prompted, enter the PIN shown on the RealPresence Content Pod home screen.
- Procedure
- Share Your Screen Using Miracast
- Stop Sharing Your Screen
- Share Content from a Device Connected to RealPresence Content Pod
- Supported HDMI Input Resolutions and Frame Rates
- UHD
- 3840 x 2160p
- 24,25,30
- OHD
- 2560 x 1440p
- 50,60
- FHD
- 2560 x 1440p
- 50,60
- WSXGA+
- 1680 x 1050
- 60
- UXGA
- 1600 x 1200
- 60
- SXGA
- 1280 x 1024
- 60,70,75,85
- HD
- 1280 x 1024
- 50,60
- XGA
- 1280 x 1024
- 60,70,75,85
- Note: The way you set the resolution and refresh rate differs, depending on the type of operating system you have. Check your computer’s manual or help topics for the appropriate steps.
- Procedure
- 1 Connect one end of an HDMI cable to the HDMI Input port on the monitor. Connect the other end of the HDMI cable to the HDMI Output port on the RealPresence Content Pod system.
- 2 If your monitor has only a DVI input port, use a DVI-HDMI adapter to connect it to the HDMI output port of the RealPresence Content Pod system.
- Supported HDMI Input Resolutions and Frame Rates
- Stop Sharing Content from a Connected Device
- Polycom Pano App
- Install RealPresence Content Companion
- Use Content Companion in Standalone Mode
- Share Content Using Polycom Content Companion
- Check Application Information
- Connect to a Room System
- Disconnect from a Room System
- Share Local Content
- Stop Sharing Local Content
- Annotation Toolbar
- Annotation Toolbar Elements
- Annotation Toolbar Elements
- 1
- Expands the view of the whiteboard, blackboard, or content to full screen.
- 2
- Highlights briefly on content to note certain areas of interest.
- 3
- Provides drawing line widths.
- 4
- Provides color selections.
- 5
- Undoes the last annotation.
- 6
- Erases annotations made on whiteboard, blackboard, or content.
- 7
- Captures a snapshot of live content.
- 8
- Provides a blank whiteboard to create annotations.
- 9
- Provides a blank blackboard to create annotations.
- 10
- Exits the current content sharing interaction screen and returns to the Home screen
- Annotation Toolbar Elements
- Annotate Content
- Erase an Annotation
- Undo an Annotation
- Use Snapshot to Annotate Content
- Stop Sharing Annotated Content
- Highlight Content
- Create a Whiteboard or Blackboard
- Exit the Annotation Toolbar
- Annotation Toolbar Elements
- Troubleshooting
11
Polycom Pano App
Topics:
● Install Polycom Pano App
● Use Polycom Pano app in Standalone Mode
● Connect to a Room System
● Disconnect from a Room System
● Share Local Content
● Stop Sharing Local Content
Polycom Pano app allows you to share local content, such as your desktop or a running application, from
a computer that is not connected directly to the Polycom Pano system.
Keep the following points in mind about Polycom Pano app:
● The application provides video-only content.
No audio is shared.
● Polycom Pano app supports any computer desktop resolution with color set to 32-bit.
● Your computer resolution can be set to anything, but Polycom Pano app scales the image to
1024x768 or 1280x720.
● If Bluetooth detection is turned on, Polycom Pano app can detect nearby room systems that are
enabled with Bluetooth broadcasting to facilitate content sharing. Note, this feature is only available
to Microsoft Windows 10 users with Bluetooth version 4.0 or higher.
● Content sent from the Polycom Pano app to the Polycom Pano is encrypted.
Install Polycom Pano app
You must install the Polycom Pano app application on a computer before you can use it to show content.
Procedure:
1 Download the installation package to your local drive.
2 Double-click the installation package.
3 Follow the on-screen instructions.
Use Polycom Pano app in Standalone Mode
Standalone mode allows you to share local content.
Polycom, Inc.