User's Guide
Table Of Contents
- Contents
- Before You Begin
- Getting Started with Polycom® Pano
- RealPresence Content Pod Power
- Power On the Content Pod System
- Procedure
- 1 Use the HDMI cable to connect the RealPresence Content Pod system to the monitor.
- 2 Connect the touch monitor USB cable.
- 3 Connect the power cord to the RealPresence Content Pod system or connect the LAN cable to power on the system by Power over Ethernet (PoE).
- 4 If it is not already connected, connect the LAN cable to the system for network connectivity.
- Procedure
- Power On Self Test (POST)
- Power Off a RealPresence Content Pod System
- Power On the Content Pod System
- RealPresence Content Pod Home Screen
- RealPresence Content Pod Power
- Share Content
- Note: The RealPresence Content Pod system does not support high-bandwidth digital content protection (HDCP). If you share HDCP-encrypted content, it is not shown.
- Share Your Screen
- Share Your Screen Using Miracast
- Procedure
- 1 Make sure the device is connected to the same Wi-Fi network as the RealPresence Content Pod system.
- 2 On the device, access the Miracast or compatible screen mirroring feature. Miracast is supported on a variety of devices that use different methods for accessing the feature. On most devices, the screen mirroring feature is accessed from the Settin...
- 3 On the device, select the name of the RealPresence Content Pod system shown on the home screen.
- 4 When prompted, enter the PIN shown on the RealPresence Content Pod home screen.
- Procedure
- Share Your Screen Using AirPlay
- Procedure
- 1 Make sure the AirPlay-enabled device is connected to the same Wi-Fi network as the RealPresence Content Pod system.
- 2 Access AirPlay on the device. On most iOS devices, the AirPlay feature is located in the Control Center that you open by swiping up from the bottom of the device. For details, check your device documentation.
- 3 Select the name of the RealPresence Content Pod system that is shown on the home screen.
- 4 When prompted, enter the PIN shown on the RealPresence Content Pod home screen.
- Procedure
- Share Your Screen Using Miracast
- Stop Sharing Your Screen
- Share Content from a Device Connected to RealPresence Content Pod
- Supported HDMI Input Resolutions and Frame Rates
- UHD
- 3840 x 2160p
- 24,25,30
- OHD
- 2560 x 1440p
- 50,60
- FHD
- 2560 x 1440p
- 50,60
- WSXGA+
- 1680 x 1050
- 60
- UXGA
- 1600 x 1200
- 60
- SXGA
- 1280 x 1024
- 60,70,75,85
- HD
- 1280 x 1024
- 50,60
- XGA
- 1280 x 1024
- 60,70,75,85
- Note: The way you set the resolution and refresh rate differs, depending on the type of operating system you have. Check your computer’s manual or help topics for the appropriate steps.
- Procedure
- 1 Connect one end of an HDMI cable to the HDMI Input port on the monitor. Connect the other end of the HDMI cable to the HDMI Output port on the RealPresence Content Pod system.
- 2 If your monitor has only a DVI input port, use a DVI-HDMI adapter to connect it to the HDMI output port of the RealPresence Content Pod system.
- Supported HDMI Input Resolutions and Frame Rates
- Stop Sharing Content from a Connected Device
- Polycom Pano App
- Install RealPresence Content Companion
- Use Content Companion in Standalone Mode
- Share Content Using Polycom Content Companion
- Check Application Information
- Connect to a Room System
- Disconnect from a Room System
- Share Local Content
- Stop Sharing Local Content
- Annotation Toolbar
- Annotation Toolbar Elements
- Annotation Toolbar Elements
- 1
- Expands the view of the whiteboard, blackboard, or content to full screen.
- 2
- Highlights briefly on content to note certain areas of interest.
- 3
- Provides drawing line widths.
- 4
- Provides color selections.
- 5
- Undoes the last annotation.
- 6
- Erases annotations made on whiteboard, blackboard, or content.
- 7
- Captures a snapshot of live content.
- 8
- Provides a blank whiteboard to create annotations.
- 9
- Provides a blank blackboard to create annotations.
- 10
- Exits the current content sharing interaction screen and returns to the Home screen
- Annotation Toolbar Elements
- Annotate Content
- Erase an Annotation
- Undo an Annotation
- Use Snapshot to Annotate Content
- Stop Sharing Annotated Content
- Highlight Content
- Create a Whiteboard or Blackboard
- Exit the Annotation Toolbar
- Annotation Toolbar Elements
- Troubleshooting
Share Content
Polycom, Inc. 8
Polycom has tested and supports the following devices:
● Microsoft Surface Book
● Microsoft Surface Pro 4
● Lumia 650 and above
● Dell XPS 13 950-80085LV Signature Edition laptop
● HP Spectre x360 13-4195nr Signature Edition 2 in 1 P
● NuVision TM800W560L Signature Edition Tablet
Procedure
1 Make sure the device is connected to the same Wi-Fi network as the Polycom Pano
system.
2 On the device, access the Miracast or compatible screen mirroring feature. Miracast is supported on
a variety of devices that use different methods for accessing the feature. On most devices, the
screen mirroring feature is accessed from the Settings menu. For details, check your device
documentation.
3 On the device, select the name of the Polycom Pano system shown on the home
screen.
4 When prompted, enter the PIN shown on the Polycom Pano home screen.
Share Your Screen Using AirPlay
You can share the screen and audio of an iPhone
®
, iPad
®
, or Mac
®
computer that is AirPlay-enabled.
Procedure
1 Make sure the AirPlay-enabled device is connected to the same Wi-Fi network as the Polycom
Pano system.
2 Access AirPlay on the device. On most iOS devices, the AirPlay feature is located in the Control
Center that you open by swiping up from the bottom of the device. For details, check your device
documentation.
3 Select the name of the Polycom Pano system that is shown on the home screen. 4 When
prompted, enter the PIN shown on the Polycom Pano home screen.
Stop Sharing Your Screen
When you are done presenting content on your Windows, Android, or iOS device, make sure you end the
sharing session.
Procedure
» Do one of the following:
End the AirPlay or Miracast screen share feature on the device.
Tap .on the content window. Confirm that you want to end the session.