Polycom® KIRK ISDN Interface Card User Guide
1. Introduction As alternative to the analogue interface to the PBX from the KIRK telecom solutions, the interface can now be digital according to the ISDN standard. Note: For more information about the PBX setup, please contact your local PBX installer. The 2 Mbps KIRK ISDN Interface Card performs a 32 channel digital interface. An advantage of using ISDN interface is that an ISDN interface provides signal speech channel concentration, leading to a much better usage of the interface capacity.
2. Setting up the KIRK ISDN Interface Card The KIRK ISDN Interface Card must be installed in Slot 0 (closest to AC main plug). Please refer to the KIRK ISDN Interface Card Installation Guide for more information about the installation of the KIRK ISDN Interface Card. The KIRK ISDN Interface Card is connected to the PBX/Network whit a RJ45 plug and the connection is as follows: 3: RxA 4: TxA 5: TxB 6: RxB The PBX/Network must be set to Master whit Layer2 CRC check turned on.
Preparing the KIRK Wireless Server 1500 for Use When preparing the KIRK Wireless Server 1500 for use it is necessary to use the Administration Program. In the Administration Program you change the flash software, register users, allow subscription of handsets and type the required pin code. 1 Open the Administration Program version 8.09 or higher to change the flash software. The Administration Program window appears. 2 Under Options, click Preferences. 14129600-HD, Ed.
3 In the Advanced Options tab, click Transfer Flash Code to CCFP. An Open dialog box appears. 4 Select the flash code in question ((1330 0180.KTB), and then click Open. The flash software will be loaded to the system. Loading the flash can take a while. 5 In the Advanced Options tab, select the Allow Subscription checkbox. Note: After registration of users you subscribe the handsets to the system. To make subscription, the system must allow subscriptions to be made.
7 Click OK to accept the code. 8 In the Advanced Options tab, click Restart System. 9 Click Close to return to the main window. 10 From the main window, click the ISDN Registration to register users. 11 Under Current User Data, type the serial No., AC No., Local No. and Standby text, and then click Create. Once the handset details have been entered into the registration screen of the Administration Program, the handset can be subscribed to the system.
Configuring the ISDN IWU. To change setting or upgrade the protocol software you use the administration software for the ISDN IWU. If not already installed, download the software from www.kirktelecom.com. 2.2 Setting up the connection 1 Connect the PC to the KIRK ISDN Interface Card (J5), and start the administration software. symbol is shown at each information in the main window and the status bar says If a “Receive – error”.
2 Click File>setup connection. Click Disconnect and Select the correct comport. Click Connect and Close. Note the “Receive – success” message on the status bar. 2.3 Uploading new flash software to the ISDN IWU card. 3 Click Advanced and select Load Flash. An Flashload dialog box appears. 4 Click Start and select the file to be downloaded and click open. 5 The download starts shortly after ant takes 4 to 5 minutes. The entire KWS1500 needs to be restarted after the download. 14129600-HD, Ed.
2.4 Changing parameters and using feature. When opening the administration software the program will with the Function Commands tab selected. Here it is possible to enable or disable a list of features. 1. Call forward and Call forward reply timer. It is possible to activate call forward individual on each handset subscribed to the system. There is 3 different types of call forward available. Call forward when Busy.
2. how to activate call forward. 1. Press the menu button on the handset and select EXT. SERVICE 2. Select CALL DIVERS. and select the wanted type of call forward. 3. Select FORWARD NUMBER and type the wanted call forward destination number. 3. How to deactivate call forward. 1. Press the menu button on the handset and select EXT. SERVICE 2. Select CALL DIVERS. and select OFF. 4. Call Waiting ON/OFF. To activate this feature set the call waiting checkbox on in the administration window.
10. EEprom Key Param. This setting defines if it should be possible to transfer key information during connect. Normally this should be possible to be able to use phone banking and other dial-inn services. Under normal operations it does not cause any problems enabling both DTMF and Keypad information. 11. Default and preset setting. In the administration software it is possible to preset all the features and setting. Select the Advanced menu and select the Load settings menu.
the function that causes problems and try to do this in a situation where there is no other traffic on the system. Send the mail to KIRK. Remember to disable the trace information in the Protocol debug tab before shutting down the administration software. 14129600-HD, Ed.
