FB3003 step bench display ASSEMBLY INSTRUCTIONS IMPORTANT Please read these instructions carefully before beginning to assemble this display. Save instructions for future reference. P.O. Box 458 27725 Danville Avenue Castle Rock, MN 55010 www.poly-tex.com REV: AA-120329 U.S.
PARTS IDENTIFICATION FB2017 END STAND (2) FB2537 STABILIZER (2) NB1923 NYLON WASHER (8) RF2552 3' x 6' BENCH TOP (1) RF2554 1'-6" x 6' BENCH TOP (2) NB1901 3/8" WING NUT (8) FT3600 NORSTAD CLIP (6) NB1924 THUMB SCREW (6) TOOLS & EQUIPMENT REQUIRED 2 No tools are required for the assembly of this product.
ASSEMBLY INSTRUCTIONS 3' x 6' BENCH TOP 1'-6" x 6' BENCH TOP 1'-6 x 6' BENCH TOP NORSTAD CLIP SEE FIGURE 1 STABILIZERS END STAND INSTRUCTIONS: 1. ATTACH BOTH STABILIZERS TO END STAND STUDS USING NYLON WASHERS AND WING NUTS. 2. PLACE ALL BENCH TOPS ON END STANDS. 3. SECURE BENCH TOPS WITH NORSTAD CLIPS AND THUMB SCREWS.
OPTIONAL BASKET TOWER PARTS IDENTIFICATION FB2002 U-BRACE (2) FB2531 CANOPY PURLIN (4) 4 FB2003 49" BASKET POST (4) NB1827 5/16" x 2" CARRIAGE BOLT (8) NB1862 5/16" LOCK WASHER (8) NB1903 5/16" WING NUT (8)
OPTIONAL BASKET TOWER ASSEMBLY INSTRUCTIONS U-BRACE CANOPY PURLIN 49" BASKET POST 49" BASKET POST ASSEMBLED FB3003 STEP DISPLAY INSTRUCTIONS: 1. INSERT 49" BASKET POSTS INTO SOCKETS ON END STANDS. 2. ATTACH U-BRACES TO 49" BASKET POSTS. 3. ATTACH CANOPY PURLINS TO U-BRACES AND 49" BASKET POSTS USING 2" LONG CARRIAGE BOLTS, LOCK WASHERS, AND WING NUTS.
OPTIONAL BASKET TOWER CANOPY OPTIONAL BASKET TOWER CANOPY PARTS IDENTIFICATION FB2531 CANOPY PURLIN (2) CANOPY (1) NB1827 - (4) NB1862 - (4) NB1903 - (4) 6
OPTIONAL BASKET TOWER CANOPY ASSEMBLY INSTRUCTIONS CANOPY CANOPY PURLIN U-BRACE 49" BASKET POST 49" BASKET POST ASSEMBLED FB3003 STEP DISPLAY W/ BASKET TOWER INSTRUCTIONS: 1. ATTACH CANOPY PURLINS TO U-BRACES USING 2" LONG CARRIAGE BOLTS, LOCK WASHERS, AND WING NUTS. 2. PLACE CANOPY OVER TOP OF CANOPY TOWER AND SECURE WITH VELCRO STRAPS.
OPTIONAL ADD-A-BENCH PARTS IDENTIFICATION RF2554 1'-6" x 6' BENCH TOP (1) FB2002B U-BRACE (2) OPTIONAL ADD-A-BENCH ASSEMBLY INSTRUCTIONS 1'-6" x 6' BENCH TOP U-BRACE INSTRUCTIONS: 1. INSERT U-BRACE LEGS INTO POCKETS ON END STANDS. NORSTAD CLIP & THUMB SCREW 2. SET BENCH TOPS DOWN ONTO U-BRACES. 3. SECURE BENCH TOPS WITH NORSTAD CLIPS & THUMB SCREWS.
ASSEMBLY INSTRUCTIONS - CONNECTED RUNS EXISTING UNIT * ADJOINING STABILIZER EXISTING END STAND * ADJOINING END STAND INSTRUCTIONS: 1. ATTACH ADJOINING UNIT'S STABILIZERS AND END STAND TO THE EXISTING UNIT'S END STAND. 2. SET BENCH TOPS DOWN OVERLAPPING EXISTING BENCH TOPS AS SHOWN BELOW. 3. SECURE CLIPS ONLY ON END UNITS OF MULTIPLE UNITS JOINED TOGETHER ( BENCH TOP (ADJOINING) * ).
OPTIONAL END CAP PARTS IDENTIFICATION FB3013 END CAP BENCH (1) FT4030 END CAP CLIP (2) FB3011 END CAP BRACKET (2) FT2570 STOP TAB (2) 10
OPTIONAL END CAP ASSEMBLY INSTRUCTIONS 1. WITH 3' x 6' BENCH TOP REMOVED, PLACE END CAP BRACKETS ON END STANDS AS SHOWN. END CAP BRACKET 2. SET 3' x 6' BENCH TOP BACK ONTO BENCH ASSEMBLY. SET END CAP BENCH ONTO BRACKETS. 3. ATTACH END CAP CLIP WITH STOP TAB, LOCK WASHER, AND WING NUT AS SHOWN IN DETAIL BELOW. REPEAT FOR OTHER END CAP BRACKET.
SAFETY GUIDELINES Do not climb, sit on, or use this product as a ladder. Injuries may occur. Do not place or install electrical items on this product. Wet conditions are typical and electrical shock may occur. Do not place this product on a slope that exceeds 3 degrees. Do not move this display after product is in place. Damage to display and injuries may occur. CARE & MAINTENANCE To remove loose soil and debris, simply spray the soiled areas with water from a garden hose.
