FB3001 fence-on-a-step-bench display ASSEMBLY INSTRUCTIONS IMPORTANT Please read these instructions carefully before beginning to assemble this display. Save instructions for future reference. US PATENT #5,553,551 P.O. Box 458 27725 Danville Avenue Castle Rock, MN 55010 www.poly-tex.com REV: AB-120329 U.S.
PARTS IDENTIFICATION FB2533 36" STABILIZER (1) FB2805 BENCH END (2) NB1923 NYLON WASHER (4) NB1901 3/8" WING NUT (4) RF2552 3' x 6' R.F. BENCH TOP (2) RF2554 1'6" x 6' R.F. BENCH TOP (1) NB1924 THUMB SCREW (6) TOOLS & EQUIPMENT REQUIRED 2 No tools are required for the assembly of this product.
ASSEMLBY INSTRUCTIONS 3/8" WING NUT NYLON WASHER 36" STABILIZER ATTACH 36" STABILIZER TO BENCH ENDS AND FASTEN WITH WING NUTS & NYLON WASHERS. PLACE BENCH TOPS IN POSITION. INSTALL NORSTAD CLIPS IN THE MIDDLE OF EACH BENCH END.
OPTIONAL BASKET PURLIN PARTS IDENTIFICATION GM4000 6'-1 1/2" BASKET PURLIN (1) 4 NB1903 5/16" WING NUT (2) FB2007 BASKET PURLIN SUPPORT (2) NB1831 5/16" x 1" CARRIAGE BOLT (2) NB1862 5/16" LOCK WASHER (2)
OPTIONAL BASKET PURLIN ASSEMBLY INSTRUCTION 5/16" X 1" CARRIAGE BOLT, LOCK WASHER & WING NUT 6'-1 1/2" BASKET PURLIN BASKET PURLIN SUPPORT INSTRUCTIONS: 1. INSERT BASKET PURLIN SUPPORTS INTO SOCKETS. 2. ATTACH BASKET PURLIN USING 5/16" X 1" CARRIAGE BOLTS, LOCK WASHERS, & WING NUTS.
OPTIONAL BASKET TOWER PARTS IDENTIFICATION FB2002C U-BRACE (2) FB2806 BENCH END W/SOCKET (2) 6 FB2531 6'-1 1/2" CANOPY PURLIN (3) FB2003 49" BASKET POST (2) FB2003C 19" BASKET POST (2) NB1827 5/16" x 2" CARRIAGE BOLT (6) NB1862 - 6 NB1903 - 6
OPTIONAL BASKET TOWER ASSEMBLY INSTRUCTION INSTRUCTIONS: 1. INSERT 49" BASKET POSTS INTO SOCKETS ON LOWER BENCHING & INSERT 19" BASKET POSTS INTO UPPER SOCKETS. 2. ATTACH U-BRACES TO 49" & 19" BASKET POST. 3. ATTACH CANOPY PURLINS TO U-BRACES AND BASKET POSTS USING 2" LONG CARRIAGE BOLT, LOCK WASHER AND WING NUT.
OPTIONAL BASKET TOWER CANOPY PARTS IDENTIFICATION FB2531 6'-1 1/2" CANOPY PURLIN (3) CANOPY (1) 8 NB1827 - 6 NB1862 - 6 NB1903 - 6
OPTIONAL BASKET TOWER CANOPY ASSEMBLY ASSEMBLED FB3001 STEP DISPLAY W/ BASKET TOWER INSTRUCTIONS: 1. ATTACH CANOPY PURLINS TO U-BRACES USING 2" LONG CARRIAGE BOLTS, LOCK WASHERS, AND WING NUTS. 2. PLACE CANOPY OVER TOP OF CANOPY TOWER AND SECURE WITH VELCRO STRAPS.
OPTIONAL A-TOWER OPTIONAL A-TOWER PARTS IDENTIFICATION NB1827 - 6 NB1862 - 6 NB1903 - 6 FB2807 BENCH END (1.
OPTIONAL A-TOWER & CANOPY ASSEMBLY CANOPY CANOPY BRACE CANOPY PURLIN INSTRUCTIONS: 1. PLACE CANOPY BRACES INTO BENCH ENDS. 2. ATTACH CANOPY PURLINS TO CANOPY BRACES WITH 5/16" x 2-1/4" LONG CARRIAGE BOLTS, LOCK WASHERS, AND WING NUTS. 3. PLACE CANOPY OVER TOWER AND SECURE WITH VELCRO STRAPS.
OPTIONAL CASTER ASSEMBLY INSTRUCTIONS INSTRUCTIONS: 1. REMOVE BOTTOM PLUGS. 2. INSTALL CASTER RAIL. 3. FASTEN WITH THUMB SCREWS. BE SURE CASTER STUB IS INSTALLED AS SHOWN IN ILLUSTRATION. THUMB SCREW ONCE DISPLAY IS IN PLACE, ALL CASTERS MUST BE LOCKED TO PREVENT MOVEMENT. THE BRAKE IS ACTIVATED BY ROTATING THE LEVER FROM THE "OFF" POSITION TO THE "ON" POSITION.
ASSEMBLY INSTRUCTIONS - CONNECTED RUNS * * * * * * BENCH TOP (ADJOINING) BENCH TOP (EXISTING) BENCH END BENCH TOP SUPPORT TUBE INSTRUCTIONS: 1. ATTACH ADJOINING UNIT'S STABILIZERS AND END STAND TO THE EXISTING UNIT'S END STAND. 2. SET BENCH TOPS DOWN OVERLAPPING EXISTING BENCH TOPS AS SHOWN BELOW. 3. SECURE CLIPS ONLY ON END UNITS OF MULTIPLE UNITS JOINED TOGETHER ( * ).
SAFETY GUIDELINES Do not climb, sit on, or use this product as a ladder. Injuries may occur. Do not place or install electrical items on this product. Wet conditions are typical and electrical shock may occur. Do not place this product on a slope that exceeds 3 degrees. Do not move this display after product is in place. Damage to display and injuries may occur. Lock casters (when provided) once display is in place to prevent movement. Remove all debris or obstacles from caster's path before moving.
