EXPANSION MANSION INSTALLATION INSTRUCTIONS : N O i th I T w C U ed g R d in i T v r S ro u N d p O l e C a s R u u n FO an for tio T m ls lla O o N r t ria sta e te i n f Re ma P.O. Box 458 27725 Danville Avenue Castle Rock, MN 55010 www.poly-tex.com AC-120813 U.S.
SAFETY GUIDELINES Read before assembling the structure WARNING This structure is intended to be self-supporting, provided it is constructed with all frames, hardware, sheathing, sheeting, bracing, cables, and membrane in place, and secured to the foundation as shown in the manual. Stability during construction, from winds and loads imposed during erection, is the sole responsibility of the installer. Observe safety codes required by your jurisdiction, and relevant safety practices for working at heights.
Index You have just purchased an Expansion Mansion. We know you will enjoy this greenhouse for a long time to come. Before you proceed, please read the instruction manual very carefully. If you have any questions please call: 1-800-852-3443 or 1-651-463-7009 P.O. Box 458 - 27725 Danville Ave Castle Rock, MN 55010 Visit our Web Site at: www.poly-tex.
HARDWARE IDENTIFICATION ( SHOWN ACTUAL SIZE)
FITTING IDENTIFICATION
SITE LAYOUT ℄ ℄
S S
TRUSS ASSEMBLY
RIDGE PURLIN & DIAGONAL STRUT ASSEMBLY
GUTTER INSTALLATION (OPTIONAL) !
END FRAME & END DOOR ASSEMBLY DOOR JAMB EXT. STOP (2) 1/4-14 X 3/4" SELF-DRILLING SCREW IMPORTANT: (2) #12-14 X 1" SELF-DRILLING SCREW DO NOT BYPASS THIS PROCEDURE! DR5070 DR5071 HOOP SECTIONS (ROUND) & END FRAMES (SQUARE) 1/4"-14 x 1" SELFDRILLING SCREW 5/16" x 3/4" HEX HEAD BOLT "A" FITTING GROUND STAKE FOOTING NOTE: BE CAREFUL NOT TO PUT THE SELF- DRILLING SCREW SO LOW THAT IT GETS IN THE WAY OF ROLL FORM.
TRUSS STABILIZER ASSEMBLY
ROLL FORM LAYOUT
END FRAME DOOR ASSEMBLY 7'-1/2"
SIDE DOOR FRAMING (OPTIONAL) 82" NOTE:
SIDE DOOR SHEETING
SIDE DOOR INSTALLATION (OPTIONAL)
ROLL FORM LAYOUT FOR ROOF SHEETING (OPTIONAL) NOTE: IMPORTANT NOTE:
SLIDE-SIDE INSTALLATION (OPTIONAL) 1 If not previously installed on page 11, install the center Roll Form Rail 22 1/2" above the second row of roll form using uni-clamps on each greenhouse frame section the full length of the greenhouse. SA4014 S.A. DIVIDER (ENLARGED & NOT TO SCALE) Measure in from the end of the top roll form rail 2-3/4" 5 and place the preassembled 2" Seat & Backer on the top rail.
SLIDE-PANEL INSTALLATION (OPTIONAL)
TAPE & ALUMINUM PROFILE LOCATION (FOR STRUCTURED SHEETING APPLICATIONS) Structured Sheet Ends Structured Sheet Roof Note: Install all foil tape before installing sheets to greenhouse DO NOT APPLY FOIL TAPE UNTIL ALL SHEETS ARE TRIMMED.
POLY-VENT INSTALLATION CORNER HOOP TUBE WIGGLE WIRE BASE (FOR POLY ROOFS) -OR"U" PROFILE (FOR STRUCTURED SHEET ROOF) BACKER PLATE TO BEGIN POLY-VENT INSTALLATION, ENSURE THE ROLL-FORMED RAIL DIMENSIONS ARE CORRECT. FOLLOW THE INSTRUCTIONS OF THE 8-1/2" x 11" POLY-VENT INSTRUCTION MANUAL. THE MANUAL VISUALLY DEPICTS 2x4 WOOD MOUNTING RAILS, BUT YOU WILL BE MOUNTING TO THE ROLL-FORMED RAILS PREVIOUSLY INSTALLED.
STRUCTURED SHEET SCREW PATTERN
STRUCTURED SHEET ROOF INSTALLATION (OPTIONAL)
3" TYP.
ROOF & END POLY SIZES
POLY FASTENER LOCATION (OPTIONAL)
INFLATION SYSTEM INSTALLATION
FAN & SHUTTER INSTALLATION (OPTIONAL)
POWER POLE & BENCHING INSTALLATION