Product Manual

IMPORTANT
Please read these instructions
carefully before you start to assemble
this greenhouse.
Keep these instructions in a safe
place for future reference.
Screws 411 and nuts 412 are used thruoghout the assembly process.
Screws 411 are to be assembled from the outside and nuts 412 from the inside of the greenhouse.
Do not fasten screws and nuts (411 & 412) more than 2-3 turns only. Do not tighten them until
completion of the panels' assembly, if not specified otherwise.
However, in some steps, temporary tightening of a few screws may be needed to prevent
a profile from falling till it will be fully connected in the next steps.
!
411412
Choose a sunny position away from
overhanging trees.
We are strongly recomend to fix your
greenhouse directly to a solid concrete
foundation. When doing that use the
pre drilled holes in the metal base
supplied.
Take out all components parts of the
packages. Sort the parts and check
against the contents parts list.
During assembly parts should be laid
out close at hand. Keep all small parts
(screws etc.) in a bowl so they do not
get lost.
In purpose to facilitate parts'
identification and assembly process, all-
positioned profiles are used in this
greenhouse. As a result some apertures
in the profiles are not used during
assembly.
Before Assembly
During Assembly
Carry out the assembly steps in the order
set out in the instructions.
Step 1: Make sure the base is square by
measuring the diagonals and level by
using a spirit level.
Step 4: Part A994 + A995 are for the
back of the greenhouse. Once in place,
you have determined the back or front
of your greenhouse.
Steps 7, 10, 13: The oval hole in the
crossbars A256 should always be
assembled to the base of the
greenhouse.
Door assembly (Steps 8, 44-50)
Door can be installed as a left hand door
or right hand door to your decision.
These instructions show a right hand
door assembly.
Step 8: determines door direction
door post 987 is where door hinges will
be located.
Steps 44-50: Door assembly should be
done according to this decision.
Steps 31-32: Decide on the window's
location before assembly. Window can
be installed in one of the indicated
options.
Step 51: If a left door is assembled, door
stopper parts should be connected to
the front left handed corner of the base
and not to the corner that is shown in
the illustration
Step 52: Firmly connect the greenhouse
to a level final position immediately after
completion of the assembly.
For assistance with assembly or for
replacement parts  please log onto our
website or call our service line (number
is on the title page).
www.palramapplications.com
Additional information can be found at
our website:
www.palramapplications.com
Customer Service
Safety Advice
It is of utmost importance to assemble
all of the parts according to the
directions. Do not skip any step.
We strongly recommend using work
gloves during assembly.
Always wear shoes and safety goggles
when working with extruded aluminium.
If using a step ladder or power tools
ensure that you follow the
manufacturer's safety advice.
Do not touch overhead power cables
with the aluminium profiles.
Do not attempt to assemble the
greenhouse in windy or wet conditions.
Dispose of all plastic bags safely keep
them out of reach of small children.
Keep children away from the assembly
area.
Do not position your greenhouse in
an area exposed to excessive wind.
Do not attempt to assemble this
greenhouse if you are tired, have taken
drugs or alcohol or if you are prone to
dizzy spell.
Hot items such as recently used grills,
blowtorches etc. must not be stored in
the greenhouse. Ensure there are no
hidden pipes or cables in the ground
before inserting the pegs.
This product is designed to use as
greenhouse only.
Care & Maintenance
When your greenhouse needs to be
cleaned, use a mild detergent solution
and rinse with cold clean water. DO NOT
use acetone, abrasive cleaners or other
special detergents to clean the clear
panels.
It is recommended to check periodically
that roof panels' caps (plastic part 329
& profile 981) are set in place.
Tools & Equipment
This is a multi-part assembly best
achieved by two people. Allow at least
half a day for assembly process.
Selecting a site - the greenhouse must
be assembeld, positioned and fixed on
a flat level surface.
Tape measure
Work gloves
Lubricant
Phillips head screwdriver
Step ladder
Drill bit
Large hammer
Spanner
T001 - Special tool for Screws 411 and nuts 412
Do not lean against or push the
greenhouse during construction.