MRD85i OWNER’S MANUAL BUILT-IN BLUETOOTH WIRELESS AUDIO SIRIUS READY DMD READY (Digital Music Device like iPod®, MP3, Smartphone devices) USB READY FLIP DOWN FRONT PANEL SD MEMORY CARD READY AM/FM MARINE STEREO RDS READY
I N S T A L L AT I O N IMPORTANT! Before mounting be sure there is sufficient room to accommodate the unit and that there is sufficient ventilation. Before installing the unit, connect the wiring temporarily making sure the system works properly. Only use the parts included with the unit to ensure proper installation. Receiver should be mounted within 30º (+ or— 15º) from Horizontal. If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance.
Optional Mounting Techniques Optional gimbal mount bracket installation Model # GM-MRD80 Optional Overhead / Under Dash mount installation Model # RM-10
WIRING DIAGRAM Wiring Details: Use the wired plug end (Pigtail) provided to make power and speaker connections according to the diagram below. Using this connector will make it easy to disconnect the radio for adding additional features or service. Removing the factory plug end will void warranty.
Wire Color Yellow Green w/stripe Green Red White w/stripe White Blue Gray w/stripe Gray Black Violet w/stripe Violet 1 2 3 4 5 6 7 8 9 10 11 12 Function B+ (+12VDC) Rear Left SpeakerRear Left Speaker+ ACC (+12VDC) Front Left SpeakerFront Left Speaker+ Relay Trigger Front Right SpeakerFront Right Speaker+ Ground (Neg) Rear Right SpeakerRear Right Speaker+ Power Wire Specifications: Yellow Wire - Connect this wire to a constant +12V source.
The Yellow, Red and Black power wires should be 14AWG or larger depending on the length to the battery. NEVER operate the unit without the proper power and ground wire. NEVER ground the speaker leads and NEVER allow the speaker leads to come in contact with each other. The speaker wire should be at least 16 gauge or larger. Be sure to observe the correct polarity on the speaker connections Use quality crimp connectors to connect wires together. Seal the connection well with electrical tape.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 23.
Bass Treble Balance Fader Subwoofer EQ Volume ID3 EQ AND SUBWOOFER SETTING Press Volume knob repeatedly until EQ menu appears then rotate the volume knob to change EQ setting selection. EQ: 1 – Optimized for Poly-Planar SP200R or SFS101 spa speakers or small diameter (3‖) flush mount speakers. MS55 subwoofer is recommended (back channels). Adjust subwoofer setting by pressing Volume Knob repeatedly until Subwoofer menu appears on the display then use Volume Knob to adjust to your desired setting.
use the Volume Knob to adjust to different setting. knob to confirm. America Australia Japan Press Function/Select Europe2 China Europe MODE SELECTION Press MODE button to choose desired listening mode. (e.g. Radio mode to USB mode to AUX IN mode… etc.) MUTE Press MUTE button to mute the sound. volume level. Press again to return to previous DIMMER CONTROL Press and hold MENU button for 3 seconds to display current setting. Then use the Volume Knob to adjust to different setting.
AUTOMATIC MEMORY STORING & PRESET SCAN (AS/PS) The PRESET buttons can be used to store 6 stations in each band (FM 1, FM 2, FM 3 and AM1, AM2) for convenient access to your favorite stations. Automatic Storing Press AS/PS button, the radio searches and checks the signal strength until one cycle search is finished then the strongest stations are stored into the corresponding preset number button automatically. Manual Storing 1. Select the desired band. 2.
TA or TP (Traffic Announcement or Traffic Program) - automatically detects travel announcements on the nearest local radio station. This facility will raise the volume of the radio or interrupt a CD or cassette to alert you to a travel announcement. You can turn the facility on or off, as required. TA operations: press MENU button until the TA settings is on display. Rotate Function/Select knob to turn on/off TA function. The ―TA‖ characters will be displayed on LCD if TA is on.
If a SIRIUS TUNER is already connected: Press MODE button to change to SIRIUS mode. If there is no SIRIUS TUNER connected this mode will be skipped. Please connect your SIRIUS Tuner to the SIRIUS port located at the back of the unit. Then press MODE button to change to SIRIUS mode. SELECTING A CHANNEL Press / button to select a channel. button to go faster. Press and Hold or SEARCHING CHANNEL NUMBER MANNUALLY Press AS/PS button ―Select: - - - ‖ will show on the display.
AUTOMATIC MEMORY STORING The PRESET buttons can be used to store 6 channels in each band (S1, S2 and S3) for convenient access to your favorite channels. 1. Select the desired band. 2. Select the channel you want to store in memory, then press and hold one of the preset buttons for 3 seconds until the corresponding preset button number appears. 3. Repeat steps 1 and 2 to program additional channels.
DISPLAY INFORMATION Press MENU button to access current display setting. If you want to change the display setting use the FUNCTION/SELECT knob to change the display setting to Artist, Song, Composer, Number, Name or Category information. i P o d ® O P E R AT I O N SWITCHING TO iPod® MODE If a device is already connected: Press MODE button to change to iPod® mode.
REPEAT PLAYING Press 3 button and select ―Repeat: ONE‖ to repeat same song or press 3 button again to select ―Repeat: All‖ to repeat same album. Press 3 button again and select ―Repeat: OFF‖ to stop repeat function. PLAYING ALL SONGS/ALBUM IN RANDOM ORDER Press 2 button to play all songs/album in random order. ―Random: Track‖ – to play all tracks in random ―Random: Album‖ – to play all album in random ―Random: OFF – to cancel the random function.
This unit can be connected to any portable music devices such as MP3 Player, TV and DVD through the AUX IN located at the back of the unit. Press MODE button to change the mode to ―AUX Input 1‖ (back) or ―AUX Input 2‖ (DMD drawer) mode. Please note: In this mode, all controls and functions must be controlled from your music device.
PREVIEWING ALL TRACKS Press 1 button to play all songs in intro mode. The unit will play the first 10 seconds of each song continuously until you press 1 button again to stop intro function. PLAYING ALL TRACKS IN RANDOM ORDER Press 2 button and select ―Random: Track‖ to play all tracks in random. Press 2 button and select ―Random: Off‖ to cancel random function. REPEAT FUNCTION Press 3 button and select ―Repeat: ONE‖ to repeat same song.
Insert SD card through the SD card port located in front of the unit. MODE button to change to SD Card mode. Press Warning!: Do not over-insert the card as this can damage the contact pins. Refer USB operation for further instructions. REMOVING THE SD CARD Firmly press the card into the slot and release it. partially out of the slot. The card should pop IMPORTANT NOTE: Some Memory Card devices may not be compatible with the unit.
Dimensions 32 × 24 × 2.1 mm C O M P AT I B L E A C C E S S O R I E S ( s o l d s e p a r a t e l y ) MR45R Wired Remote Control – connect to the back of the unit labeled ―TO MR45R‖. You can add up to 2 MR45R in conjunction with CMR-Y7. MRR21 IR Wireless Remote Control - the IR eye is located next to the volume button and must be in line of site for the remote to operate. MRRF18 RF Wireless Remote Control with Receiver – simply connect the receiver to the IR port located at the back of the unit.
TROUBLESHOOTING PROBLEM CAUSE No power Blown fuse, power wires disconnected No sound Mute is on, Volume set at minimum, wiring is not properly connected Cannot read some USB devices This unit is not 100% compatible with all USB devices or the USB devices has special format. The battery may be too low (the unit operating voltage is 10.8v to 15.6v). This is normal. The unit sometimes takes longer time to read all the files inside the USB device or SD Card.
T E C H N I C A L S P E C I F I C AT I O N S TUNER(AM) Frequency Range Usable Sensitivity 530-1710 KHz 32 dBuV TUNER(FM) Frequency Range Channel Step Sensitivity Stereo Separation Signal to Noise Ratio 87.5-107.9 MHz 200KHz 2.8 uV 30dB 50dB LINE-OUT Output Impedance 5 Volt ( max ) 33 Ohm GENERAL 12V DC (10.8-15.6V allowable) Speaker Impedance 4 or 8 ohm Output Power 45W x 4CH Fuse 15A NOTE: Specification & design subject to change without notice for improvements.
