Operation Manual

2. CONNECTION OF ACCESSORIES (see page 4)
All the Vaporetto Lecoaspira accessories can be connected
directly to the flexible steam/vacuum hose or to the extension
hoses.
2.1 To connect the specific accessories for the suction and
steaming features proceed as follows:
Move the locknut of the accessory, if
present, to the OPEN position and connect
the accessories.
Move the accessory locknut to the CLOSED
position. Check the strength of the
connection.
On the extension tubes there is an
additional fastening button: proceed as
described previously for the accessories
and release the tubes by sliding the button
as far as the lock position.
2.2 To connect the special accessories only for suction it is only
necessary to attach them without coupling them to the locknut.
2.3 To connect the steam lance with the steam concentrator,
simply screw it on. The same operation can be carried out for the
coloured brushes, which can in turn be screwed onto the steam
concentrator and onto the steam lance. The different colours
allow you to always use the same brush for the same surface.
3. INTEGRATED CLEANING PROGRAMS
The appliance is equipped with preset programmes to
automatically regulate the steam pressure and the duration of
suction based on the surface in question.
3.1 Press the SET button on the control panel. When it is turned
on, the appliance starts in manual mode. Using the buttons
and it is possible to select the desired programme. Confirm
the selection by pressing the OK button.
To change the programme again, repeat the operation indicated
above.
4. MANUAL OPERATION
In this mode, it is possible to manually adjust the quantity of
steam dispensed and the suction speed.
Make sure that you have prepared the appliance following the
instructions provided in Chapter 1.
4.1 For suction only, press the suction button on the appliance
and proceed with cleaning.
The suction power can be adjusted, based on the surface to be
cleaned, by holding the suction button down. In this case the
number of segments on the suction indicators will increase or
decrease on the appliance control panel.
Hold the suction button down to stop suction.
4.2 For steam cleaning only, switch on the boiler using the
button . The pressure and boiler indicators will start flashing.
Select the steam pressure desired by pressing the button
again. One of the 4 pressure indicators lights up every time the
button is pressed, indicating the increase in the pressure of the
steam. Press the button to reduce the steam pressure. One of
the pressure indicators goes off every time the button is
pressed, showing the reduction in the steam pressure.
When the pressure indicator and the boiler indicator remain lit,
it means that the appliance has reached the desired steam
pressure.
Ensure that the steam lock on the handle is deactivated. Hold
the steam trigger to dispense steam, the relative indicator will
turn on.
To stop the steam flow, simply release the steam button.
4.3 For steam cleaning and suction, carry out points 4.1 and 4.2
at the same time.
Steam
Maximum
4 indicators
turned on
To remove scaling, stains, and
grease and sanitise
Regular
steam
2 or 3 indicators
turned on
For carpets, rugs, windows,
floors
Minimum
steam
1 indicator
turned on
To steam plants, clean delicate
fabrics, wall coverings, sofas, etc.
FAV70
FAV80
On the appliance, under the handle, there is a handy label
listing the number and type of programmes.
WARNING: The preset programmes can vary depending on
the Lecoaspira model chosen.
To avoid any dirt in the dirt collector causing bad smells, we
recommend emptying and cleaning after every use according
to the methods described in Chapter 22.
For safety reasons, engage the steam lock on the handle
during vacuuming.
Level 1 Curtains
Level 2 Sofas and cushions
Level 3 Rugs and carpets
Level 4 Floor or liquid collection
When the appliance is switched on again, the suction level will
be that set last time it was used.
| 28|
ENGLISH
PRELIMINARE LECOASPIRA FAV70_80 - 2015_vers7:UNICO 04/05/2015 17.28 Pagina 28