User manual
Product overview
Operation
Do not set up or operate the product under water.
Make sure that the cables hang loosely and are not
stretched too tightly. Failure to heed this warning may
cause the cables to tear.
Do not operate the product if it is still in its packaging.
Lay the product out entirely before connecting it to the
power supply.
Do not hang any objects from the product and do not
cover the product.
The LEDs are neither dimmable nor replaceable.
1. Insert the ground spike into the solar panel bracket. Place
the solar panel bracket with the ground spike onto the solar
panel mount. Pay attention to the arrows on the solar panel
when mounting/dismantling.
2. Connect the plug on the light chain to the socket on the solar
panel cable. It is only possible to connect the plug in one
orientation.
3. Secure the connection by turning the screw cap on the plug
onto the socket thread.
4. Choose a suitable mounting location with a soft surface.
Rocky surfaces damage the ground spike. Carefully push the
solar panel with the ground spike into the surface to around
1/3 of the length of the spike/holder or deeper in order to
ensure a sucient hold.
Place the solar panel in a location with sucient light so that
the solar cells can charge the battery throughout the day. The
solar cells should not be covered or placed in the shade, e.g.
in the shade of trees or buildings.
5. Place the light chain on the branches of a tree or bush. If
necessary, use plastic cable ties for additional support.
6. Before using for the first time, the product requires
approximately 8 hours of sunlight to charge the battery.
7. To turn on the product, press the on/o button on the
bottom of the solar panel.
8. Press the MODE FLASH button on the bottom of the solar
panel to switch between constant light and flashing light.
9. Turn the product o after use with the on/o button.
The battery is always charged when the sun shines on the
solar cells, regardless of whether the product is on or o.
The rechargeable battery of the solar panel is not replaceable.
If the light chain does not turn on when the battery has been
charged, dispose of the product properly.
Maintenance and cleaning
•The product is maintenance-free apart from occasional
cleaning.
•Switch the product o before cleaning and let the LEDs cool
down suciently.
•To clean, use a clean, dry, lint-free cloth. For stubborn dirt,
slightly dampen the cloth with water. Allow the product to dry
completely before continued use.
Disposal
Electronic devices are recyclable waste and must not
be disposed of in the household waste. At the end of its
service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute
to the protection of the environment.
Technical data
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited. The operating instructions
reflect the current technical specifications at time of print.
© Copyright 2015 by CEI Conrad Electronic International (HK) Limited
PSL-03-001-002-003_v1_0615_02_m_EN
distributed by Conrad Electronic SE,
Klaus-Conrad-Str. 1, D-92240 Hirschau
Item No. PSL-03-001 PSL-03-002 PSL-03-003
Protection type IP44
Operating voltage NiMH
battery,
1,2 V,
1200 mAh
NiMH
battery,
1,2 V,
800 mAh
NiMH
battery,
1,2 V,
2000 mAh
Power consumption 1.92 W 0.96 W 4.8 W
Number of lights 40 20 100
Luminous colour Warm white
Lighting time 8 - 10 h
Power cable length 5 m
Total length 8.9 m 6.9 m 14.9 m
Distance between
lights
10 cm
Operating conditions -20 to +70 °C / 0 – 90 % RH
Storage conditions -20 to +70 °C / 0 – 90 % RH
Weight 250 g 200 g 400 g
5 m
6.9 m
20 cm
5 m
14.9 m
10 cm
PSL-03-002
PSL-03-003
PSL-03-001
5 m
8.9 m
10 cm