Service Manual
Table Of Contents
- 2008 RANGER RZR SERVICE MANUAL
- GENERAL INFORMATION
- MAINTENANCE
- PERIODIC MAINTENANCE CHART
- COMPONENT INSPECTION / SERVICE LOCATIONS
- LUBRICANTS / SERVICE PRODUCTS
- MAINTENANCE REFERENCES
- GENERAL VEHICLE INSPECTION AND MAINTENANCE
- FUEL SYSTEM AND AIR INTAKE
- ENGINE
- TRANSMISSION AND GEARCASES
- COOLING SYSTEM
- FINAL DRIVE / WHEEL AND TIRE
- ELECTRICAL AND IGNITION SYSTEM
- STEERING AND SUSPENSION
- BRAKE SYSTEM
- ENGINE
- ENGINE SPECIFICATIONS
- ENGINE COOLING SYSTEM
- GENERAL ENGINE SERVICE
- ENGINE DISASSEMBLY AND INSPECTION
- Cylinder Head Assembly Exploded View
- Rocker Arms
- Push Rods
- Cylinder Head Removal
- Cylinder Head Inspection
- Cylinder Head Warp
- Valve Seal / Spring Service (On Engine)
- Cylinder Head Disassembly
- Valve Inspection
- Combustion Chamber
- Valve Seat Reconditioning
- Cylinder Head Reassembly
- Valve Sealing Test
- Cylinder Removal
- Valve Lifter Removal / Inspection
- Piston Removal
- Cylinder Inspection
- Cylinder Hone Selection and Honing Procedure
- Honing To Deglaze
- Cleaning the Cylinder After Honing
- Piston-to-Cylinder Clearance
- Piston / Rod Inspection
- Piston Ring Installed Gap
- Starter Drive Bendix Removal / Inspection
- Flywheel / Stator Removal / Inspection
- Engine Crankcase Disassembly / Inspection
- Camshaft Inspection
- ENGINE REASSEMBLY
- ENGINE INSTALLATION
- TROUBLESHOOTING
- ELECTRONIC FUEL INJECTION
- GENERAL INFORMATION
- FUEL TANK
- ELECTRONIC FUEL INJECTION
- ELECTRONIC CONTROL UNIT (ECU)
- TEMPERATURE AND BAROMETRIC AIR PRESSURE SENSOR (T-BAP)
- CRANKSHAFT POSITION SENSOR (CPS)
- FUEL INJECTORS
- FUEL PUMP
- FUEL PRESSURE REGULATOR
- THROTTLE POSITION SENSOR (TPS)
- ENGINE COOLANT TEMPERATURE SENSOR (ECT)
- IGNITION COIL
- GENERAL TROUBLESHOOTING
- EFI SYSTEM BREAKOUT DIAGRAMS
- Diagnostic Connector Circuit
- Malfunction Indicator Lamp (MIL) Circuit
- Fuel Injector (PTO) Circuit
- Fuel Injector (MAG) Circuit
- Engine Coolant Temperature Sensor (ECT) Circuit
- Engine Overheat Lamp Driver Circuit
- Crankshaft Position Sensor (CPS) Circuit
- Air Temperature and Barometric Air Pressure Sensor (T-BAP) Circuit
- Throttle Position Sensor (TPS) Circuit
- Fuel Pump Circuit
- BODY / STEERING / SUSPENSION
- CLUTCHING
- FINAL DRIVE
- TRANSMISSION
- BRAKES
- GENERAL SPECIFICATIONS
- TORQUE SPECIFICATIONS
- SPECIAL TOOLS
- BRAKE SYSTEM SERVICE NOTES
- BRAKE NOISE TROUBLESHOOTING
- HYDRAULIC BRAKE SYSTEM OPERATION
- BRAKE SYSTEM EXPLODED VIEW
- MASTER CYLINDER
- BRAKE PEDAL LEVER
- BRAKE BLEEDING / FLUID CHANGE
- FRONT BRAKE PADS
- FRONT CALIPER SERVICE
- FRONT BRAKE DISC
- REAR BRAKE PAD
- REAR CALIPER SERVICE
- REAR BRAKE DISC
- TROUBLESHOOTING
- ELECTRICAL
- General Information
- Switches / Controls
- Instrument Cluster
- Instrument Cluster Troubleshooting Tests
- All Wheel Drive Coil
- Gear Position Indicator Switch
- Speed Sensor
- Head Lights
- Tail / Brake / Work Lights
- Cooling System Schematic
- EFI Diagnostics
- Fuel Sender
- Relays
- Fuse Box Layout
- Fuses / Circuit Breaker
- Charging System
- Battery Service
- Conventional Battery
- Low Maintenance Battery
- Starting System
- Starting System Testing Flow Chart
- Electrical BreakOut Diagrams
- INDEX
- WIRE DIAGRAMS
7.17
FINAL DRIVE
7
12. Remove the roll cage assembly and rollers from the clutch
housing. Use a shop towel to cover the housing in order to
retain all the rollers.
NOTE: Rollers are spring loaded. Take care not to
allow them to fall out or lose them upon removal of
the roll cage.
13. Thoroughly clean all parts and inspect the rollers (A) for
nicks and scratches. The rollers must slide up and down and
in and out freely within the roll cage sliding surfaces and
H-springs.
14. Inspect the roll cage assembly (B) sliding surfaces and H-
springs. The sliding surfaces must be clean and free of
nicks, burrs or scratches. If damaged, replace the roll cage
assembly.
15. Inspect clutch housing ring gear (C) for a consistent wear
pattern. Inspect the ring gear for chipped, broken, or
missing teeth.
16. Inspect both output hub assemblies. Inspect the bearings
and replace if needed.
Gearcase Assembly / Inspection
1. As mentioned during gearcase disassembly section,
replace all O-rings, seals, and worn components.
2. Press the pinion shaft seal into the pinion cover, until the
seal is flush with the sealing surface.
3. If bearing replacement was required, press new bearings on
to the pinion shaft assembly.
4. Install pinion shaft, bearings, and pinion cover with new
O-ring and torque screws to 7-11 ft. lbs. (10-15 Nm).
A
C
B
B
H-Spring
Pinion Cover Screw Torque:
7-11 ft. lbs. (10-15 Nm)
Bearing
Spacer
Roller
Thrust
Bearing
Surface
Torque
Screws