Service Manual
Table Of Contents
- 2008 RANGER RZR SERVICE MANUAL
- GENERAL INFORMATION
- MAINTENANCE
- PERIODIC MAINTENANCE CHART
- COMPONENT INSPECTION / SERVICE LOCATIONS
- LUBRICANTS / SERVICE PRODUCTS
- MAINTENANCE REFERENCES
- GENERAL VEHICLE INSPECTION AND MAINTENANCE
- FUEL SYSTEM AND AIR INTAKE
- ENGINE
- TRANSMISSION AND GEARCASES
- COOLING SYSTEM
- FINAL DRIVE / WHEEL AND TIRE
- ELECTRICAL AND IGNITION SYSTEM
- STEERING AND SUSPENSION
- BRAKE SYSTEM
- ENGINE
- ENGINE SPECIFICATIONS
- ENGINE COOLING SYSTEM
- GENERAL ENGINE SERVICE
- ENGINE DISASSEMBLY AND INSPECTION
- Cylinder Head Assembly Exploded View
- Rocker Arms
- Push Rods
- Cylinder Head Removal
- Cylinder Head Inspection
- Cylinder Head Warp
- Valve Seal / Spring Service (On Engine)
- Cylinder Head Disassembly
- Valve Inspection
- Combustion Chamber
- Valve Seat Reconditioning
- Cylinder Head Reassembly
- Valve Sealing Test
- Cylinder Removal
- Valve Lifter Removal / Inspection
- Piston Removal
- Cylinder Inspection
- Cylinder Hone Selection and Honing Procedure
- Honing To Deglaze
- Cleaning the Cylinder After Honing
- Piston-to-Cylinder Clearance
- Piston / Rod Inspection
- Piston Ring Installed Gap
- Starter Drive Bendix Removal / Inspection
- Flywheel / Stator Removal / Inspection
- Engine Crankcase Disassembly / Inspection
- Camshaft Inspection
- ENGINE REASSEMBLY
- ENGINE INSTALLATION
- TROUBLESHOOTING
- ELECTRONIC FUEL INJECTION
- GENERAL INFORMATION
- FUEL TANK
- ELECTRONIC FUEL INJECTION
- ELECTRONIC CONTROL UNIT (ECU)
- TEMPERATURE AND BAROMETRIC AIR PRESSURE SENSOR (T-BAP)
- CRANKSHAFT POSITION SENSOR (CPS)
- FUEL INJECTORS
- FUEL PUMP
- FUEL PRESSURE REGULATOR
- THROTTLE POSITION SENSOR (TPS)
- ENGINE COOLANT TEMPERATURE SENSOR (ECT)
- IGNITION COIL
- GENERAL TROUBLESHOOTING
- EFI SYSTEM BREAKOUT DIAGRAMS
- Diagnostic Connector Circuit
- Malfunction Indicator Lamp (MIL) Circuit
- Fuel Injector (PTO) Circuit
- Fuel Injector (MAG) Circuit
- Engine Coolant Temperature Sensor (ECT) Circuit
- Engine Overheat Lamp Driver Circuit
- Crankshaft Position Sensor (CPS) Circuit
- Air Temperature and Barometric Air Pressure Sensor (T-BAP) Circuit
- Throttle Position Sensor (TPS) Circuit
- Fuel Pump Circuit
- BODY / STEERING / SUSPENSION
- CLUTCHING
- FINAL DRIVE
- TRANSMISSION
- BRAKES
- GENERAL SPECIFICATIONS
- TORQUE SPECIFICATIONS
- SPECIAL TOOLS
- BRAKE SYSTEM SERVICE NOTES
- BRAKE NOISE TROUBLESHOOTING
- HYDRAULIC BRAKE SYSTEM OPERATION
- BRAKE SYSTEM EXPLODED VIEW
- MASTER CYLINDER
- BRAKE PEDAL LEVER
- BRAKE BLEEDING / FLUID CHANGE
- FRONT BRAKE PADS
- FRONT CALIPER SERVICE
- FRONT BRAKE DISC
- REAR BRAKE PAD
- REAR CALIPER SERVICE
- REAR BRAKE DISC
- TROUBLESHOOTING
- ELECTRICAL
- General Information
- Switches / Controls
- Instrument Cluster
- Instrument Cluster Troubleshooting Tests
- All Wheel Drive Coil
- Gear Position Indicator Switch
- Speed Sensor
- Head Lights
- Tail / Brake / Work Lights
- Cooling System Schematic
- EFI Diagnostics
- Fuel Sender
- Relays
- Fuse Box Layout
- Fuses / Circuit Breaker
- Charging System
- Battery Service
- Conventional Battery
- Low Maintenance Battery
- Starting System
- Starting System Testing Flow Chart
- Electrical BreakOut Diagrams
- INDEX
- WIRE DIAGRAMS
5.18
BODY / STEERING / SUSPENSION
4. Use a press and correct size driver to remove the ball joint
from the A-arm.
NOTE: The driver must fit the ball joint housing in
the A-arm. This will allow the ball joint to be properly
pressed out of the A-arm without damaging the A-
arm.
Installation
1. Place the A-arm in the correct position for ball joint
installation. Face the A-arm end flat on top of the driver.
Carefully drive the ball joint into place until the ball joint
is properly seated.
2. After the new ball joint is installed into the A-arm, install
a NEW retaining ring.
3. Reinstall the A-arm (see “FRONT A-ARMS - Removal /
Replacement”).
4. Repeat the ball joint service procedure for any additional
A-arm ball joint replacements.
Correct
Driver Placement
The driver must fit the
inside diameter of the
Upper A-arm Shown
A-arm end.
Press out of the A-arm
in this direction
Upper A-arm Shown
Place driver HERE
to support A-arm
Press into the A-arm
in this direction
Upper A-arm Shown
Place driver HERE
to support A-arm
Ball Joint
Upper A-arm
NEW
Retaining Ring