Service Manual
Table Of Contents
- 2008 RANGER RZR SERVICE MANUAL
- GENERAL INFORMATION
- MAINTENANCE
- PERIODIC MAINTENANCE CHART
- COMPONENT INSPECTION / SERVICE LOCATIONS
- LUBRICANTS / SERVICE PRODUCTS
- MAINTENANCE REFERENCES
- GENERAL VEHICLE INSPECTION AND MAINTENANCE
- FUEL SYSTEM AND AIR INTAKE
- ENGINE
- TRANSMISSION AND GEARCASES
- COOLING SYSTEM
- FINAL DRIVE / WHEEL AND TIRE
- ELECTRICAL AND IGNITION SYSTEM
- STEERING AND SUSPENSION
- BRAKE SYSTEM
- ENGINE
- ENGINE SPECIFICATIONS
- ENGINE COOLING SYSTEM
- GENERAL ENGINE SERVICE
- ENGINE DISASSEMBLY AND INSPECTION
- Cylinder Head Assembly Exploded View
- Rocker Arms
- Push Rods
- Cylinder Head Removal
- Cylinder Head Inspection
- Cylinder Head Warp
- Valve Seal / Spring Service (On Engine)
- Cylinder Head Disassembly
- Valve Inspection
- Combustion Chamber
- Valve Seat Reconditioning
- Cylinder Head Reassembly
- Valve Sealing Test
- Cylinder Removal
- Valve Lifter Removal / Inspection
- Piston Removal
- Cylinder Inspection
- Cylinder Hone Selection and Honing Procedure
- Honing To Deglaze
- Cleaning the Cylinder After Honing
- Piston-to-Cylinder Clearance
- Piston / Rod Inspection
- Piston Ring Installed Gap
- Starter Drive Bendix Removal / Inspection
- Flywheel / Stator Removal / Inspection
- Engine Crankcase Disassembly / Inspection
- Camshaft Inspection
- ENGINE REASSEMBLY
- ENGINE INSTALLATION
- TROUBLESHOOTING
- ELECTRONIC FUEL INJECTION
- GENERAL INFORMATION
- FUEL TANK
- ELECTRONIC FUEL INJECTION
- ELECTRONIC CONTROL UNIT (ECU)
- TEMPERATURE AND BAROMETRIC AIR PRESSURE SENSOR (T-BAP)
- CRANKSHAFT POSITION SENSOR (CPS)
- FUEL INJECTORS
- FUEL PUMP
- FUEL PRESSURE REGULATOR
- THROTTLE POSITION SENSOR (TPS)
- ENGINE COOLANT TEMPERATURE SENSOR (ECT)
- IGNITION COIL
- GENERAL TROUBLESHOOTING
- EFI SYSTEM BREAKOUT DIAGRAMS
- Diagnostic Connector Circuit
- Malfunction Indicator Lamp (MIL) Circuit
- Fuel Injector (PTO) Circuit
- Fuel Injector (MAG) Circuit
- Engine Coolant Temperature Sensor (ECT) Circuit
- Engine Overheat Lamp Driver Circuit
- Crankshaft Position Sensor (CPS) Circuit
- Air Temperature and Barometric Air Pressure Sensor (T-BAP) Circuit
- Throttle Position Sensor (TPS) Circuit
- Fuel Pump Circuit
- BODY / STEERING / SUSPENSION
- CLUTCHING
- FINAL DRIVE
- TRANSMISSION
- BRAKES
- GENERAL SPECIFICATIONS
- TORQUE SPECIFICATIONS
- SPECIAL TOOLS
- BRAKE SYSTEM SERVICE NOTES
- BRAKE NOISE TROUBLESHOOTING
- HYDRAULIC BRAKE SYSTEM OPERATION
- BRAKE SYSTEM EXPLODED VIEW
- MASTER CYLINDER
- BRAKE PEDAL LEVER
- BRAKE BLEEDING / FLUID CHANGE
- FRONT BRAKE PADS
- FRONT CALIPER SERVICE
- FRONT BRAKE DISC
- REAR BRAKE PAD
- REAR CALIPER SERVICE
- REAR BRAKE DISC
- TROUBLESHOOTING
- ELECTRICAL
- General Information
- Switches / Controls
- Instrument Cluster
- Instrument Cluster Troubleshooting Tests
- All Wheel Drive Coil
- Gear Position Indicator Switch
- Speed Sensor
- Head Lights
- Tail / Brake / Work Lights
- Cooling System Schematic
- EFI Diagnostics
- Fuel Sender
- Relays
- Fuse Box Layout
- Fuses / Circuit Breaker
- Charging System
- Battery Service
- Conventional Battery
- Low Maintenance Battery
- Starting System
- Starting System Testing Flow Chart
- Electrical BreakOut Diagrams
- INDEX
- WIRE DIAGRAMS
4.14
ELECTRONIC FUEL INJECTION
3. If the resistance is correct.
- Test the main harness circuit between the sensor
connector terminals and the corresponding pin terminals at
the ECU (see wiring diagram).
- Check the sensor mounting, air gap, flywheel ring gear for
damage or runout, and flywheel key. Follow the “CPS
Replacement” procedure to inspect CPS and flywheel ring
gear for damage.
4. If the resistance is incorrect, follow the “CPS Replacement”
procedure.
CPS Replacement
Removal
1. Safely support the rear of the vehicle off the ground and
remove the left-hand rear tire.
2. If not done already; disconnect the CPS harness connector
(see illustration under “CPS Test”).
IMPORTANT: In order to remove the CPS, the rear
portion of the exhaust system and the mounting
bracket between the transmission and rear gearcase
will need to be removed.
3. Remove the exhaust pipe between the elbow pipe and the
exhaust silencer. Remove the exhaust silencer.
4. Remove the (3) bolts retaining the front portion of the
mounting bracket to the transmission. Retain the bolts,
washers, and spacers for installation.
5. Remove the bottom bolt that attaches the bracket to the rear
gearcase through the hole in the frame support as shown.
6. Remove the (2) remaining fasteners that attach the bracket
to the side of the rear gearcase.
7. Remove the bolt from the bracket at the front of the rear
gearcase.
WARNING
Serious injury may result if machine tips or falls.
Be sure the vehicle is secure before beginning
this service procedure.
Remove
Remove
Silencer
Elbow
Header
Pipe
Pipe
Rear Gearcase
Mounting Bolt
Transmission
Mounting Bolts