Service Manual
Table Of Contents
- GENERAL INFORMATION
- MAINTENANCE
- ELECTRONIC FUEL INJECTION
- SPECIAL TOOLS
- Part Numbers / Descriptions
- Fuel Pressure Gauge Kit - PU-43506-A
- Fuel Pressure Gauge Adaptor - PS-48762
- Throttle Position Sensor Tester Kit - 2201519
- Digital Wrench™ Diagnostic Software PU-47063
- Digital Wrench™ SmartLink Module Kit - PU-47471
- Digital Wrench™ - Diagnostic Connector
- Digital Wrench™ - Download Website
- FUEL TANK
- FUEL LINE
- EFI SERVICE NOTES
- EFI SYSTEM LAYOUT
- EFI COMPONENTS
- ELECTRONIC FUEL INJECTION
- ELECTRONIC CONTROL UNIT (ECU)
- FUEL PUMP
- FUEL PRESSURE REGULATOR
- FUEL INJECTORS
- CRANKSHAFT POSITION SENSOR (CPS)
- TEMP / MANIFOLD ABSOLUTE PRESSURE SENSOR (T-MAP)
- IDLE AIR CONTROL VALVE (IAC)
- THROTTLE POSITION SENSOR (TPS)
- ENGINE COOLANT TEMPERATURE SENSOR (ECT)
- IGNITION COIL
- EFI DIAGNOSTICS
- FUEL SYSTEM TROUBLESHOOTING
- EFI SYSTEM BREAK-OUT DIAGRAMS
- Fuel Injector Circuit (PTO)
- Fuel Injector Circuit (MAG)
- Idle Air Control (IAC) Circuit
- Crankshaft Position Sensor (CPS) Circuit
- Fuel Pump / Fuel Level Sensor Circuit
- Fuel Pump Circuit
- Fuel Gauge Circuit
- Engine Coolant Temperature Sensor (ECT) Circuit
- Throttle Position Sensor (TPS) Circuit
- Intake Air Temperature / Manifold Absolute Pressure Sensor (T-MAP) Circuit
- Diagnostic Connector Circuit
- Diagnostic Connector Circuit (EPS Models)
- SPECIAL TOOLS
- COOLING SYSTEM
- ENGINE
- GENERAL INFORMATION - ENGINE
- ENGINE ASSEMBLY VIEWS AND TORQUE VALUES
- Torque & Torque Sequence - Main Engine Components
- Valve Cover / Breather Valve
- Camshaft Carrier / Camshaft / Rocker Arm
- Cylinder Head / Valve / IAFM
- Valve & Spring Height Detail
- Piston / Connecting Rod
- Crankshaft
- Crankcase
- Crankcase - Upper
- Balance Shaft / Balance Shaft Timing
- Crankcase (Lower) With Oil Pump
- Water Pump Coupler
- Water Pump / Water Pump Coupler / Stator / Flywheel
- Drive Coupler (Rear) / Starter Gear
- ENGINE SERVICE
- ENGINE DISASSEMBLY AND INSPECTION
- Valve Cover / Breather Valve
- Rocker Carrier / Camshaft Removal
- Rocker Arm / Rocker Arm Shaft Inspection
- Camshaft / Camshaft Bore Inspection
- Cylinder Head Removal
- Cylinder Head Cleaning
- Cylinder Head Warp Inspection
- Cylinder Head
- Valve Inspection
- Combustion Chamber
- Valve Guide Removal / Installation
- Valve Seat Reconditioning
- Cylinder Head Assembly
- Valve Sealing Test
- Cylinder Head Installation
- Camshaft / Carrier Assembly
- Camshaft / Camshaft Carrier Installation
- Camshaft Timing
- Cam Chain Tensioner Installation
- Camshaft Timing - Quick Reference
- Crankcase Disassembly
- Crankcase (Lower) / Oil Pump Disassembly
- Crankcase Disassembly (Upper)
- Piston / Connecting Rod Removal
- Counterbalance Shaft Removal / Inspection
- Counterbalance Split Gear Replacement
- Crankshaft / Cam Chain Removal
- Cam Chain / Sprocket Inspection
- Crankcase Inspection (Lower)
- Crankshaft Inspection
- Connecting Rod Inspection
- Connecting Rod Big End Bearing Selection
- Piston / Piston Ring Inspection
- Piston Ring Removal
- Piston Ring Installed Gap
- Piston Pin Bore Inspection
- Cylinder Inspection
- Piston-to-Cylinder Clearance
- Honing - Important Information
- ENGINE ASSEMBLY
- Crankcase Preparation - Upper
- Piston Ring Installation
- Piston / Connecting Rod Assembly
- Piston / Connecting Rod Installation
- Crankshaft Installation
- Oil Passage Tube
- Crankcase Assembly - Upper
- Balance Shaft Installation
- Balance Shaft Timing
- Crankcase Preparation (Lower)
- Crankcase Sealant and Torque Values
- Crankcase Assembly
- WATER PUMP
- TROUBLESHOOTING
- TRANSMISSION
- CLUTCHING (PVT)
- FINAL DRIVE
- BODY / FRAME
- STEERING / SUSPENSION
- BRAKES
4.11
COOLING SYSTEM
4
Stator Cover Assembly Torque Specifications
Use weather strip or contact cement
to hold damper rubber (A) on water
pump coupler nut (B) during stator
cover installation.
A
B
Crankshaft Position Sensor (CPS)
89 in. lbs.
(10 Nm)
Coolant
Fitting
1/8 NPTF
Coolant
Pipe
TORQUE SEQUENCE
89 in. lbs.
(10 Nm)
Lubricate
New O-Rings