Service Manual
Table Of Contents
- GENERAL INFORMATION
- MAINTENANCE
- ELECTRONIC FUEL INJECTION
- SPECIAL TOOLS
- Part Numbers / Descriptions
- Fuel Pressure Gauge Kit - PU-43506-A
- Fuel Pressure Gauge Adaptor - PS-48762
- Throttle Position Sensor Tester Kit - 2201519
- Digital Wrench™ Diagnostic Software PU-47063
- Digital Wrench™ SmartLink Module Kit - PU-47471
- Digital Wrench™ - Diagnostic Connector
- Digital Wrench™ - Download Website
- FUEL TANK
- FUEL LINE
- EFI SERVICE NOTES
- EFI SYSTEM LAYOUT
- EFI COMPONENTS
- ELECTRONIC FUEL INJECTION
- ELECTRONIC CONTROL UNIT (ECU)
- FUEL PUMP
- FUEL PRESSURE REGULATOR
- FUEL INJECTORS
- CRANKSHAFT POSITION SENSOR (CPS)
- TEMP / MANIFOLD ABSOLUTE PRESSURE SENSOR (T-MAP)
- IDLE AIR CONTROL VALVE (IAC)
- THROTTLE POSITION SENSOR (TPS)
- ENGINE COOLANT TEMPERATURE SENSOR (ECT)
- IGNITION COIL
- EFI DIAGNOSTICS
- FUEL SYSTEM TROUBLESHOOTING
- EFI SYSTEM BREAK-OUT DIAGRAMS
- Fuel Injector Circuit (PTO)
- Fuel Injector Circuit (MAG)
- Idle Air Control (IAC) Circuit
- Crankshaft Position Sensor (CPS) Circuit
- Fuel Pump / Fuel Level Sensor Circuit
- Fuel Pump Circuit
- Fuel Gauge Circuit
- Engine Coolant Temperature Sensor (ECT) Circuit
- Throttle Position Sensor (TPS) Circuit
- Intake Air Temperature / Manifold Absolute Pressure Sensor (T-MAP) Circuit
- Diagnostic Connector Circuit
- Diagnostic Connector Circuit (EPS Models)
- SPECIAL TOOLS
- COOLING SYSTEM
- ENGINE
- GENERAL INFORMATION - ENGINE
- ENGINE ASSEMBLY VIEWS AND TORQUE VALUES
- Torque & Torque Sequence - Main Engine Components
- Valve Cover / Breather Valve
- Camshaft Carrier / Camshaft / Rocker Arm
- Cylinder Head / Valve / IAFM
- Valve & Spring Height Detail
- Piston / Connecting Rod
- Crankshaft
- Crankcase
- Crankcase - Upper
- Balance Shaft / Balance Shaft Timing
- Crankcase (Lower) With Oil Pump
- Water Pump Coupler
- Water Pump / Water Pump Coupler / Stator / Flywheel
- Drive Coupler (Rear) / Starter Gear
- ENGINE SERVICE
- ENGINE DISASSEMBLY AND INSPECTION
- Valve Cover / Breather Valve
- Rocker Carrier / Camshaft Removal
- Rocker Arm / Rocker Arm Shaft Inspection
- Camshaft / Camshaft Bore Inspection
- Cylinder Head Removal
- Cylinder Head Cleaning
- Cylinder Head Warp Inspection
- Cylinder Head
- Valve Inspection
- Combustion Chamber
- Valve Guide Removal / Installation
- Valve Seat Reconditioning
- Cylinder Head Assembly
- Valve Sealing Test
- Cylinder Head Installation
- Camshaft / Carrier Assembly
- Camshaft / Camshaft Carrier Installation
- Camshaft Timing
- Cam Chain Tensioner Installation
- Camshaft Timing - Quick Reference
- Crankcase Disassembly
- Crankcase (Lower) / Oil Pump Disassembly
- Crankcase Disassembly (Upper)
- Piston / Connecting Rod Removal
- Counterbalance Shaft Removal / Inspection
- Counterbalance Split Gear Replacement
- Crankshaft / Cam Chain Removal
- Cam Chain / Sprocket Inspection
- Crankcase Inspection (Lower)
- Crankshaft Inspection
- Connecting Rod Inspection
- Connecting Rod Big End Bearing Selection
- Piston / Piston Ring Inspection
- Piston Ring Removal
- Piston Ring Installed Gap
- Piston Pin Bore Inspection
- Cylinder Inspection
- Piston-to-Cylinder Clearance
- Honing - Important Information
- ENGINE ASSEMBLY
- Crankcase Preparation - Upper
- Piston Ring Installation
- Piston / Connecting Rod Assembly
- Piston / Connecting Rod Installation
- Crankshaft Installation
- Oil Passage Tube
- Crankcase Assembly - Upper
- Balance Shaft Installation
- Balance Shaft Timing
- Crankcase Preparation (Lower)
- Crankcase Sealant and Torque Values
- Crankcase Assembly
- WATER PUMP
- TROUBLESHOOTING
- TRANSMISSION
- CLUTCHING (PVT)
- FINAL DRIVE
- BODY / FRAME
- STEERING / SUSPENSION
- BRAKES
7.23
CLUTCHING (PVT)
7
Clutch Bushing Removal
1. Install main puller adapter (Item 8) onto puller.
2. Install adapter reducer (Item 9).
3. Using a hand held propane torch, apply heat around outside
of bushing until tiny smoke tailings appear.
4. Flip sheave over so bushing faces downward and install
onto puller.
5. Install bushing tool (Item 2).
6. Install left hand nut (C) and spacer onto puller rod and
tighten by hand. Turn puller barrel for further tension if
needed.
7. Turn clutch sheave counterclockwise until bushing is
removed and sheave comes free.
8. Remove nut (C) (left hand thread) from puller rod and set
aside.
9. Remove adapters from puller.
10. Remove bushing and removal tool from adapters. Discard
bushing.
Clutch Bushing Installation
1. Install puller adapter (Item 10) onto puller.
2. Install adapter (Item 9) onto puller.
3. Apply Loctite 609 evenly to bushing bore inside
moveable sheave.
4. Install sheave face down on puller.
5. Install new bushing on installation tool (Item 2) and install
assembly into sheave.
6. Install left hand thread nut (C) onto puller rod and hand
tighten against installation tool.
7. Turn clutch sheave counterclockwise, making sure bushing
is drawn straight into bore. Continue until bushing is
seated.
8. Remove nut (C) from puller rod and set aside.
9. Remove installation tool and clutch sheave from puller.