Owners manual

ManualsBrandsPoison Spyder ManualsAutomotive17-08-410-ALUM Body Armor Fits 07-18 Wrangler (JK)

INSTALLATION INSTRUCTIONS

JK BODY ARMOR INSTALLATION

Thank you for purchasing Poison Spyder Body

Armor for your Jeep JK. Although it is a lengthy

procedure, Installation is fairly simple with the

right tools and good mechanical abilities. If

you are not condent in your mechanical skills,

please seek the help of a professional to perform

the installation. Please read through these entire

instructions before proceeding with installation.

PARTS LIST

(1) Driver side Body Armor panel

(1) Passenger side Body Armor Panel

(1) Nut Insert installation tool

The following items are provided only for Rocker Knockers

with Sliders, and vary by model:

2-DR 4-DR

(34) (42) 1/4-20 nut-sert

(34) (42) 1/4-20X3/4 SS at head cap screw

TOOLS NEEDED

• Bar clamps (2 or more)

• 1/2” drill motor

• 1/4” drill bit

• 25/64” drill bit

• Hammer

• 1/4” center punch

• 7/16” box end wrench

• 9/16” box end wrench

• 5/32” hex key

• 1/4” drive ratchet

• 10mm 1/4” drive socket

• 13mm 1/4” drive socket

• Anti-seize compound

• Fine tip felt marker

• Masking tape

• Touch- up paint

• A friend to hold parts in place

BEFORE YOU BEGIN

• It is imperative that you read and follow

instructions to ensure that you will have a

successful installation.

• Failure to do so may result in an unsatisfactory

installation.

• It is the purchaser/installer’s responsibility to

inspect the package for any missing pieces

prior to beginning installation.

• Carefully read the product warranty and

hold harmless agreement at the end of this

document

• Read through instructions thoroughly before

beginning installation.

INSTALL PREPARATION:

1. Parkvehicleonalevel surface and set the

emergency brake. You will want to wear eye

protection beyond this point in time.

2. Ifyour Wrangleris a Rubicon edition or it

is equipped with rocker protection or steps,

they will now need to be removed. Factory

installed rocker protection is held on by:

a. 2-Door: four (4) nuts in the pinch weld

ange (Figure 1) and two (2) bolts that

go into the bottom of the tub (Figure 2).

Summary of content (5 pages)

PAGE 1
Thank you for purchasing Poison Spyder Body Armor for your Jeep JK. Although it is a lengthy procedure, Installation is fairly simple with the right tools and good mechanical abilities. If you are not confident in your mechanical skills, please seek the help of a professional to perform the installation. Please read through these entire instructions before proceeding with installation.
PAGE 2
b. 4-Door: six (6) nuts in the pinch weld flange (Figure 1) and three (3) bolts that go into the bottom of the tub (Figure 2). FIGURE 1 Using the 1/4” drive ratchet, 10mm socket and the 13mm socket remove the hardware that fastens the rocker protection to the Jeep. Page 2 INSTALLATION INSTRUCTIONS Poison Spyder Customs • JK BODY ARMOR INSTALLATION at least ten (10) inches. This step will help eliminate scratches during installation. 4.
PAGE 3
Page 3 INSTALLATION INSTRUCTIONS Poison Spyder Customs • JK BODY ARMOR INSTALLATION 14. Remove the tape from the back of the Body Armor. 15. (Optional) If you purchased the rubber liners, they will need to be placed on the back side of the Body Armor. Use a couple of bolts to help hold the liner in place. FIGURE 5 7. Install the Body Armor using two 1/4” flat head bolts. Make sure you place a small amount of anti-seize on each bolt.
PAGE 4
FIGURE 9 18. Remove the masking tape from the front and rear fender flares. 19. Tighten all bolts to no more that 10 ft./lbs. 20. Reinstall rocker protection if you removed any. 21. Repeat the procedure for the passenger side. ©2009 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.
PAGE 5
WARRANTY Poison Spyder Customs™ warranties all of the products we sell and distribute for one (1) year from the date of sale. These products will be free from defects in material and workmanship under normal installation, and use. Due to the intended use the powder coat finish is warranted for ninety (90) days. The finish warranty will not cover a product if it has been damaged in any way. Warranty is limited to repair or replacement.