User's Manual
Table Of Contents
- 1. Introduction
- 2. Safety Regulations
- 3. Getting Started
- 4. Get to Know Your Device
- 4.1. Feature of Your Device
- 4.2. PM260 Handy Terminal
- 4.3. Front Panel Layout
- 4.4. Display Backlight
- 4.5. Keypad Backlight
- 4.6. Using Screen Protectors
- 4.7. Installing Your Screen Protector
- 4.8. Back Panel Layout
- 4.9. Left Side Panel Layout
- 4.10. Installing Memory Cards
- 4.11. Right Side Panel Layout
- 4.12. Top Panel Layout
- 4.13. Bottom Panel Layout
- 4.14. Peripherals and Accessories
- 4.15. USB ActiveSync Cable
- 4.16. Li-ion Battery Packs
- 4.17. Battery Power
- 4.18. Main Battery Pack
- 4.19. Managing Main Battery Power
- 4.20. Storage Guidelines
- 4.21. Internal Backup Battery
- 4.22. Resetting the Terminal
- 4.23. Suspend Mode
- 4.24. Memory Allocation
- 4.25. Care and Cleaning of the Products
- 4.26. PM260 Technical Specifications
- 5. Using the Keypad
- 6. Using the Image Engine
- 7. Using the Laser Engine
- 8. Using ScanWedge
- 9. Using Control Panel
- 9.1. System Properties
- 9.2. General
- 9.3. Memory
- 9.4. Device name
- 9.5. Copyrights
- 1.1.
- 9.6. Power properties
- 9.7. Battery tab
- 1.1.
- 1.1.
- 1.1.
- 1.1.
- 9.8. Power off tab
- 9.9. CPU Power Setting Tab
- 9.10. Alerts Tab
- 1.1.
- 9.11. Wakeup Source Tab
- 9.12. Program Button properties
- 9.13. Program Buttons Tab
- 1.1.
- 1.1.
- 9.14. Key define Tab
- 9.15. Backlight Properties
- 9.16. Battery power Tab
- 9.17. External power Tab
- 9.18. Keyboard backlight Tab
- 9.19. Scanner Settings
- 9.20. Scanner Settings Applet
- 10. Communication
- 10.1. Communication Options
- 10.2. Installing Additional Software
- 10.3. Connecting the USB ActiveSync Cable
- 10.4. ActiveSync Communication
- 10.5. Communication Type
- 10.6. Hardware Requirements for Setup
- 10.7. Software Requirements for Communication
- 10.8. Setting Up the Host Workstation
- 10.9. Setting Up the Handy Terminal
- 10.10. Communicating with the Handy Terminal
- 10.11. Synchronizing with the Host Workstation
- 10.12. Exploring the Terminal from the Workstation
- 10.13. Adding Programs via ActiveSync
- 10.14. Wireless Radios
- 10.15. Connecting the Terminal to a Wireless Network
- 10.16. WLAN (802.11b/g/n Radio)
- 10.17. Adding Programs from the Internet
- 11. Bluetooth Handler
- 12. Single Slot Docking cradle/Single Slot Ethernet cradle Device
- 12.1. Overview
- 12.2. Battery Charging
- 12.3. Power Supply
- 12.4. Front Panel
- 12.5. Back Panel
- 12.6. Powering the Single Slot Docking Cradle or Single Slot Ethernet Cradle Device
- 12.7. Charging the Main Battery
- 12.8. Inserting a Terminal
- 12.9. Charging a Spare Battery
- 12.10. Charging Backup Battery
- 12.11. Technical Specifications
Laser Light Label
If the above laser light label is attached to your device, it indicates the product contains a
laser engine or laser aimer that emits the laser light. The following information is provided to
comply with the rules imposed by international authorities and refers to the correct use of
PM260 handy terminal.
Laser Safety Statement
This product has been tested in accordance with and complies with CDRH 21 CFR 1040.10 and
1040.11 and IEC 60825-1 Ed 2 (2007) except for deviations pursuant to Laser Notice No 50, dated
June 24, 2007. LASER LIGHT. DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. 1 mW MAX
OUTPUT: 650nm.
For installation, use and maintenance, it is not necessary to open the device.
WARNING:
Do not attempt to open or otherwise service any components in the optics cavity. Opening or
servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations. The optics
system is a factory only repair item.
WARNING:
Use of controls or adjustments or performance of procedures other than those specified herein may
result in exposure to hazardous visible laser light.
WARNING:
Use of optical systems with the scanner will increase eye hazard. Optical instruments include
binoculars, microscopes, eye glasses and magnifying glasses.
8