User's Manual
Table Of Contents
- 1. Introduction
- 2. Safety Regulations
- 3. Getting Started
- 4. Get to Know Your Device
- 4.1. Feature of Your Device
- 4.2. PM260 Handy Terminal
- 4.3. Front Panel Layout
- 4.4. Display Backlight
- 4.5. Keypad Backlight
- 4.6. Using Screen Protectors
- 4.7. Installing Your Screen Protector
- 4.8. Back Panel Layout
- 4.9. Left Side Panel Layout
- 4.10. Installing Memory Cards
- 4.11. Right Side Panel Layout
- 4.12. Top Panel Layout
- 4.13. Bottom Panel Layout
- 4.14. Peripherals and Accessories
- 4.15. USB ActiveSync Cable
- 4.16. Li-ion Battery Packs
- 4.17. Battery Power
- 4.18. Main Battery Pack
- 4.19. Managing Main Battery Power
- 4.20. Storage Guidelines
- 4.21. Internal Backup Battery
- 4.22. Resetting the Terminal
- 4.23. Suspend Mode
- 4.24. Memory Allocation
- 4.25. Care and Cleaning of the Products
- 4.26. PM260 Technical Specifications
- 5. Using the Keypad
- 6. Using the Image Engine
- 7. Using the Laser Engine
- 8. Using ScanWedge
- 9. Using Control Panel
- 9.1. System Properties
- 9.2. General
- 9.3. Memory
- 9.4. Device name
- 9.5. Copyrights
- 1.1.
- 9.6. Power properties
- 9.7. Battery tab
- 1.1.
- 1.1.
- 1.1.
- 1.1.
- 9.8. Power off tab
- 9.9. CPU Power Setting Tab
- 9.10. Alerts Tab
- 1.1.
- 9.11. Wakeup Source Tab
- 9.12. Program Button properties
- 9.13. Program Buttons Tab
- 1.1.
- 1.1.
- 9.14. Key define Tab
- 9.15. Backlight Properties
- 9.16. Battery power Tab
- 9.17. External power Tab
- 9.18. Keyboard backlight Tab
- 9.19. Scanner Settings
- 9.20. Scanner Settings Applet
- 10. Communication
- 10.1. Communication Options
- 10.2. Installing Additional Software
- 10.3. Connecting the USB ActiveSync Cable
- 10.4. ActiveSync Communication
- 10.5. Communication Type
- 10.6. Hardware Requirements for Setup
- 10.7. Software Requirements for Communication
- 10.8. Setting Up the Host Workstation
- 10.9. Setting Up the Handy Terminal
- 10.10. Communicating with the Handy Terminal
- 10.11. Synchronizing with the Host Workstation
- 10.12. Exploring the Terminal from the Workstation
- 10.13. Adding Programs via ActiveSync
- 10.14. Wireless Radios
- 10.15. Connecting the Terminal to a Wireless Network
- 10.16. WLAN (802.11b/g/n Radio)
- 10.17. Adding Programs from the Internet
- 11. Bluetooth Handler
- 12. Single Slot Docking cradle/Single Slot Ethernet cradle Device
- 12.1. Overview
- 12.2. Battery Charging
- 12.3. Power Supply
- 12.4. Front Panel
- 12.5. Back Panel
- 12.6. Powering the Single Slot Docking Cradle or Single Slot Ethernet Cradle Device
- 12.7. Charging the Main Battery
- 12.8. Inserting a Terminal
- 12.9. Charging a Spare Battery
- 12.10. Charging Backup Battery
- 12.11. Technical Specifications
compliant device to facilitate USB communication to and from the terminal. USB
communication occurs through Microsoft ActiveSync (v.4.1 or higher). For more information
about ActiveSync setup, see ActiveSync Communication on paragraph 10.4.
Serial Port
The serial port supports serial communication between the terminal and another device.
Note that the connector is a DB9 Male connector, requiring a female connector on the serial
cable.
The following four signals are supported:
• Transmitted Data
• Received Data
• Request to Send
• Clear to Send
☞NOTE:
ActiveSync is not supported over the serial port.
Ethernet Port (Single Slot Ethernet cradle only)
Using an Ethernet cable, you can connect the Single Slot Ethernet cradle to an Ethernet-compliant
device to facilitate Ethernet communication to and from the terminal. This equipment is for indoor
use only. The communication wiring is limited to the inside of a building.
12.6.
Powering the Single Slot Docking Cradle or Single Slot
Ethernet Cradle Device
The terminal requires DC 5V input for communication and battery charging; the power adapter on
the power cable converts the voltage from the power source
to DC 5V. Only power adapter cables from Pointmobile
convert the voltage appropriately.
The same power cable that ships with each terminal can be
used to power the base. This cable contains a plug adapter
for each geography (US, UK, EU, etc.).
1. Attach the appropriate plug adapter to the power adapter.
2. Plug the power cable into the power source.
3. Plug the connector into the DC power jack on the back
panel. The base is now powered.
61