User's Manual
Table Of Contents
- 1. Introduction
- 2. Safety Regulations
- 3. Getting Started
- 4. Get to Know Your Device
- 4.1. Feature of Your Device
- 4.2. PM260 Handy Terminal
- 4.3. Front Panel Layout
- 4.4. Display Backlight
- 4.5. Keypad Backlight
- 4.6. Using Screen Protectors
- 4.7. Installing Your Screen Protector
- 4.8. Back Panel Layout
- 4.9. Left Side Panel Layout
- 4.10. Installing Memory Cards
- 4.11. Right Side Panel Layout
- 4.12. Top Panel Layout
- 4.13. Bottom Panel Layout
- 4.14. Peripherals and Accessories
- 4.15. USB ActiveSync Cable
- 4.16. Li-ion Battery Packs
- 4.17. Battery Power
- 4.18. Main Battery Pack
- 4.19. Managing Main Battery Power
- 4.20. Storage Guidelines
- 4.21. Internal Backup Battery
- 4.22. Resetting the Terminal
- 4.23. Suspend Mode
- 4.24. Memory Allocation
- 4.25. Care and Cleaning of the Products
- 4.26. PM260 Technical Specifications
- 5. Using the Keypad
- 6. Using the Image Engine
- 7. Using the Laser Engine
- 8. Using ScanWedge
- 9. Using Control Panel
- 9.1. System Properties
- 9.2. General
- 9.3. Memory
- 9.4. Device name
- 9.5. Copyrights
- 1.1.
- 9.6. Power properties
- 9.7. Battery tab
- 1.1.
- 1.1.
- 1.1.
- 1.1.
- 9.8. Power off tab
- 9.9. CPU Power Setting Tab
- 9.10. Alerts Tab
- 1.1.
- 9.11. Wakeup Source Tab
- 9.12. Program Button properties
- 9.13. Program Buttons Tab
- 1.1.
- 1.1.
- 9.14. Key define Tab
- 9.15. Backlight Properties
- 9.16. Battery power Tab
- 9.17. External power Tab
- 9.18. Keyboard backlight Tab
- 9.19. Scanner Settings
- 9.20. Scanner Settings Applet
- 10. Communication
- 10.1. Communication Options
- 10.2. Installing Additional Software
- 10.3. Connecting the USB ActiveSync Cable
- 10.4. ActiveSync Communication
- 10.5. Communication Type
- 10.6. Hardware Requirements for Setup
- 10.7. Software Requirements for Communication
- 10.8. Setting Up the Host Workstation
- 10.9. Setting Up the Handy Terminal
- 10.10. Communicating with the Handy Terminal
- 10.11. Synchronizing with the Host Workstation
- 10.12. Exploring the Terminal from the Workstation
- 10.13. Adding Programs via ActiveSync
- 10.14. Wireless Radios
- 10.15. Connecting the Terminal to a Wireless Network
- 10.16. WLAN (802.11b/g/n Radio)
- 10.17. Adding Programs from the Internet
- 11. Bluetooth Handler
- 12. Single Slot Docking cradle/Single Slot Ethernet cradle Device
- 12.1. Overview
- 12.2. Battery Charging
- 12.3. Power Supply
- 12.4. Front Panel
- 12.5. Back Panel
- 12.6. Powering the Single Slot Docking Cradle or Single Slot Ethernet Cradle Device
- 12.7. Charging the Main Battery
- 12.8. Inserting a Terminal
- 12.9. Charging a Spare Battery
- 12.10. Charging Backup Battery
- 12.11. Technical Specifications
by warranty.
WARNING:
DO NOT attempt to charge damp/wet handy terminals or batteries. All components must be dry
before connecting to an external power source.
12.4.
Front Panel
Terminal Well
Place the Handy Terminal in the terminal well to communicate with a host device, power
the terminal, and charge the terminal’s battery. Make sure that the device is securely seated.
Rubber Feet
The bottom panel has four rubber feet to stabilize the unit on a flat surface. You can set the
base on a dry, stable surface, such as a desktop or workbench near an electrical outlet.
12.5.
Back Panel
DC Power Jack
Connect the power cable to this power jack; see Powering the Docking cradle Device on
paragraph 12.6.
USB Port
The USB port is full-speed (v2.0). Using the USB cable, you can connect the base to a USB-
Single Slot Docking Cradle
Single Slot Ethernet Cradle
60