User's Manual
Table Of Contents
- 1. Introduction
- 2. Safety Regulations
- 3. Getting Started
- 4. Get to Know Your Device
- 4.1. Feature of Your Device
- 4.2. PM260 Handy Terminal
- 4.3. Front Panel Layout
- 4.4. Display Backlight
- 4.5. Keypad Backlight
- 4.6. Using Screen Protectors
- 4.7. Installing Your Screen Protector
- 4.8. Back Panel Layout
- 4.9. Left Side Panel Layout
- 4.10. Installing Memory Cards
- 4.11. Right Side Panel Layout
- 4.12. Top Panel Layout
- 4.13. Bottom Panel Layout
- 4.14. Peripherals and Accessories
- 4.15. USB ActiveSync Cable
- 4.16. Li-ion Battery Packs
- 4.17. Battery Power
- 4.18. Main Battery Pack
- 4.19. Managing Main Battery Power
- 4.20. Storage Guidelines
- 4.21. Internal Backup Battery
- 4.22. Resetting the Terminal
- 4.23. Suspend Mode
- 4.24. Memory Allocation
- 4.25. Care and Cleaning of the Products
- 4.26. PM260 Technical Specifications
- 5. Using the Keypad
- 6. Using the Image Engine
- 7. Using the Laser Engine
- 8. Using ScanWedge
- 9. Using Control Panel
- 9.1. System Properties
- 9.2. General
- 9.3. Memory
- 9.4. Device name
- 9.5. Copyrights
- 1.1.
- 9.6. Power properties
- 9.7. Battery tab
- 1.1.
- 1.1.
- 1.1.
- 1.1.
- 9.8. Power off tab
- 9.9. CPU Power Setting Tab
- 9.10. Alerts Tab
- 1.1.
- 9.11. Wakeup Source Tab
- 9.12. Program Button properties
- 9.13. Program Buttons Tab
- 1.1.
- 1.1.
- 9.14. Key define Tab
- 9.15. Backlight Properties
- 9.16. Battery power Tab
- 9.17. External power Tab
- 9.18. Keyboard backlight Tab
- 9.19. Scanner Settings
- 9.20. Scanner Settings Applet
- 10. Communication
- 10.1. Communication Options
- 10.2. Installing Additional Software
- 10.3. Connecting the USB ActiveSync Cable
- 10.4. ActiveSync Communication
- 10.5. Communication Type
- 10.6. Hardware Requirements for Setup
- 10.7. Software Requirements for Communication
- 10.8. Setting Up the Host Workstation
- 10.9. Setting Up the Handy Terminal
- 10.10. Communicating with the Handy Terminal
- 10.11. Synchronizing with the Host Workstation
- 10.12. Exploring the Terminal from the Workstation
- 10.13. Adding Programs via ActiveSync
- 10.14. Wireless Radios
- 10.15. Connecting the Terminal to a Wireless Network
- 10.16. WLAN (802.11b/g/n Radio)
- 10.17. Adding Programs from the Internet
- 11. Bluetooth Handler
- 12. Single Slot Docking cradle/Single Slot Ethernet cradle Device
- 12.1. Overview
- 12.2. Battery Charging
- 12.3. Power Supply
- 12.4. Front Panel
- 12.5. Back Panel
- 12.6. Powering the Single Slot Docking Cradle or Single Slot Ethernet Cradle Device
- 12.7. Charging the Main Battery
- 12.8. Inserting a Terminal
- 12.9. Charging a Spare Battery
- 12.10. Charging Backup Battery
- 12.11. Technical Specifications
Basic
Scanning
Trigger timeout (sec)
Specifies the trigger time out in
seconds. If a barcode is not
decoded within the specified
timeout, the default Notifier
indicates that decoding is failed
Enable Auto Scan
Enable Auto Scan with specified
interval.
Auto Scan interval (sec) Set Auto Scan interval time.
Continuous Scan
Enable Continuous Scan without
any interval.
Enable Center
Window(IT5300SR
device
only)
Enable Center window. Bar
codes are decoded only if they
are within the specified windows
Decode Mode(IT5300SR
device only)
Standard:
Quick Omni
(By default)
:
Delay Before
Decoding(IT5300SR
device only)
Start to decoding after specified
milliseconds
Values: 0(default)
, 100, 200,
300, 400, 500, 600,
700, 800, 900, 1000
Wedge mode
User Message
Select Result Type
User Message
Keyboard Event
Clipboard(default)
Terminator
Select the desired barcode end
method from the pull down list.
Values: None, CRLF, Space,
Tab
Power Save Options
(N4313 device only)
Power Save Mode
Select Power Save Mode
OFF
SLEEP
HIBERNATE(default)
Power Save TimeOut
(sec)
1~65535
Notification
Beep
If enabled
– plays audio sound
Volume Set sounds volume.
Good read Set sound to indicate good read.
Bad read Set sound to indicate bad read.
LED
Enable Enable visual scan indicators.
Vibrator
If enabled
- Turn on LED for good/bad
scan indicator
Good read
Set vibration time after
good read.
Bad read
Set vibration time after
bad read.
Wedge
Barcode ID
Transmit Barcode ID
Enable to transmit predefined
barcode ID in Detail tab
Label
Prefix
Enter Prefix to be sent prior to
the decoded/received data.
50