User's Manual
Table Of Contents
- 1. Introduction
- 2. Safety Regulations
- 3. Getting Started
- 4. Get to Know Your Device
- 4.1. Feature of Your Device
- 4.2. PM260 Handy Terminal
- 4.3. Front Panel Layout
- 4.4. Display Backlight
- 4.5. Keypad Backlight
- 4.6. Using Screen Protectors
- 4.7. Installing Your Screen Protector
- 4.8. Back Panel Layout
- 4.9. Left Side Panel Layout
- 4.10. Installing Memory Cards
- 4.11. Right Side Panel Layout
- 4.12. Top Panel Layout
- 4.13. Bottom Panel Layout
- 4.14. Peripherals and Accessories
- 4.15. USB ActiveSync Cable
- 4.16. Li-ion Battery Packs
- 4.17. Battery Power
- 4.18. Main Battery Pack
- 4.19. Managing Main Battery Power
- 4.20. Storage Guidelines
- 4.21. Internal Backup Battery
- 4.22. Resetting the Terminal
- 4.23. Suspend Mode
- 4.24. Memory Allocation
- 4.25. Care and Cleaning of the Products
- 4.26. PM260 Technical Specifications
- 5. Using the Keypad
- 6. Using the Image Engine
- 7. Using the Laser Engine
- 8. Using ScanWedge
- 9. Using Control Panel
- 9.1. System Properties
- 9.2. General
- 9.3. Memory
- 9.4. Device name
- 9.5. Copyrights
- 1.1.
- 9.6. Power properties
- 9.7. Battery tab
- 1.1.
- 1.1.
- 1.1.
- 1.1.
- 9.8. Power off tab
- 9.9. CPU Power Setting Tab
- 9.10. Alerts Tab
- 1.1.
- 9.11. Wakeup Source Tab
- 9.12. Program Button properties
- 9.13. Program Buttons Tab
- 1.1.
- 1.1.
- 9.14. Key define Tab
- 9.15. Backlight Properties
- 9.16. Battery power Tab
- 9.17. External power Tab
- 9.18. Keyboard backlight Tab
- 9.19. Scanner Settings
- 9.20. Scanner Settings Applet
- 10. Communication
- 10.1. Communication Options
- 10.2. Installing Additional Software
- 10.3. Connecting the USB ActiveSync Cable
- 10.4. ActiveSync Communication
- 10.5. Communication Type
- 10.6. Hardware Requirements for Setup
- 10.7. Software Requirements for Communication
- 10.8. Setting Up the Host Workstation
- 10.9. Setting Up the Handy Terminal
- 10.10. Communicating with the Handy Terminal
- 10.11. Synchronizing with the Host Workstation
- 10.12. Exploring the Terminal from the Workstation
- 10.13. Adding Programs via ActiveSync
- 10.14. Wireless Radios
- 10.15. Connecting the Terminal to a Wireless Network
- 10.16. WLAN (802.11b/g/n Radio)
- 10.17. Adding Programs from the Internet
- 11. Bluetooth Handler
- 12. Single Slot Docking cradle/Single Slot Ethernet cradle Device
- 12.1. Overview
- 12.2. Battery Charging
- 12.3. Power Supply
- 12.4. Front Panel
- 12.5. Back Panel
- 12.6. Powering the Single Slot Docking Cradle or Single Slot Ethernet Cradle Device
- 12.7. Charging the Main Battery
- 12.8. Inserting a Terminal
- 12.9. Charging a Spare Battery
- 12.10. Charging Backup Battery
- 12.11. Technical Specifications
2.4. LED Safety
The LED output on this device has met IEC62471 LED safety and certified to be under the limits of a
CLASS 1 LED product.
2.5. FCC RF Exposure
This device complies with FCC RF exposure guidelines set forth for an uncontrolled environment.
2.6. CB Scheme
This device complies with CB Scheme IEC 60950-1
2.7. FCC Part 15 Regulation
Pursuant to part 15 of the FCC Rules, you are cautioned that changes or modifications not expressly
approved by Pointmobile could void your authority to operate the PM260 handy terminal.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
In accordance with FCC 15.21, changes or modifications not expressly approved by the party
responsible for compliance could void the user‘s authority to operate the equipment.
The antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter. To maintain compliance with FCC RF exposure guidelines for body-worn operation,
do not use accessories that contain metallic components.
2.8. Canadian Compliance
This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
9