User Manual

TURNIGY Manual for Brushless Motor
Speed Gontroller
cases: The connection between ESC and motor is not reliable,
the
propeller
or the motor is blocked,
the
gearbox
is damaged, etc.)
2. Over-heat
protection:
When the temperature of the ESC is over
110 Celsius degrees, the ESC will reduce the
output
powel
3. Throttle signal loss
protection:
The ESC will reduce
the output
power
if throttle
signal
is lost for
1 second, further loss for 2 seconds
will cause
its
output
to be
cutoff
completely.
Eiiiii&n.effiiip&
xffi
Several
"beepr
tones
should be emitted,
presenting
the number
of lithium battery cells
ffi3(Throttlerangeshouldberesetwhenanewtransmitterisbeingused)
l-"^," t^r"t*
",i"k;l
G""""" b;fi]
I
uottor and then
| |
pact
to
EsC,
I
I
switch on transmitter.
| |
special tone
like
I
I ll'j, 123" means I
I
po*",
"rppry
i" ox
I
|y;il""r":'1*'tl tr',"',,"',.
;-1
Ery"*1][:]1|
l;d;l l-c"""*t
t".*-1
I
transmitter,
ll
pack
to ESC,
I
I move throttte ll and wait
for
I
I
sticr to top
|
|
auoutzsemnos
I
"Beep-Beep-'
tone
should be emitted,
means lhroltle range
highest
point
has
been
correctlv confirmed
Move throftle stick to the
bottom, several'beep: 1sn""
should be
emitted,
presenting
the number
of battery
cells
A long "Beepi' tone should
be emifted, means throttle
range lowest
point
has
been correctly confirmed
-3-
1. Enter rrogram Moqe
Switch on transmitter, move throttle stick to top
position,
connect baftery
pack
to ESC, wait for 2 se6nds, "beep-beep" tone should be
emitted. Then wait
for
another 5 seconds,
special
tone like
".! 567
r2"
should
be emitted. whlch means
prooram
mode is entered.
z, Detecr rrogrammaore [ems
Now
vou'll
hear B tones in a loop. When a lonq
"beep---"
tone is
emitted. move throttle stick to bottom to enter the
"Start
Mode"
J, JeI tlem
varue (rrogrammaore varue,
"Beep:', *u;,
tor
a
"econds;
"Beep.-beepl',
wait for another
3 seconds, then
you'll
hear
"beep-beep-beep",
move throttle stick to top
position,
then a special
tone
,,
"irtsl
g',
is emitted, now
you
have set the
,'Start
Mode" item to the value of.Super_Soft'
4. trXtr
tsrogram Moqe
After the special tone
"
,l'isis",
move throttle stick to bottom within 2 seconds.
After
power
on, motor can't
work, no
sound is emitted
connection between battery
and ESC is not OK
After
power
on, motor
can'l work, such
an alert tone is emitted:
"beep-beep-,
beep-beep-,beep-beep-'
(Every
"beep-beep]
has a time interual
lnput voltage is abnormal, too high
or too low
Check the voltage of battery
pack
After
power
on, motor can't
work, such
an
alert tone is emitted:
"beep-,
beep-, beep-
"(Every "beep]
has
Check the cable of throttle channel
power
on, motor can't
work,
such
a
alert
tone is emitted:
"beep-,
beep-, beepi
(Every
"beepj'
has
a
time interual about 0.25
Throttle
stick is not in
bottom( lowest)
position
After
power
on,
m-otor cant work, a
special tone
".!58712'
is emitted after
2
reve6ed, so the ESC has entered
The motor runs in opposite
direction The mnnection between ESC and
the motor need to be
Swap any two wire connections between ESC and
molor
The motor stop running
while in working
siate
Check the receiver and transmitter
Check the mble of throttle channel
Land RC model
as soon as
possible,
and then
reDlace the battery oack
Check all the connections:
baftery
pack
conneclion,
throttle signal
cable, motor connections, etc.