User Manual
TURNIGY
Manual for
Brushless
Motor Speed
Controller
TURNIGY
Manual
for Brushless
Motor
Speed
Gontroller
-
TroubldShooting Prggran
FSC
with
ir3nsmitier
({
Siepe}i
1 .
Enter
program
mode
2. Select
programmable
items
3. Set
item value
(Programmable
value)
4 Exrt
proqram
mode
Normal
startup
procodur€:
Trouble
Possible Reason
power
on, motor cant
work,
no The
connectaon between battery
n2ck end FSC is not OK
Check
the
power
connection
Reolace the connector.
After
power
on, motor can't
work, such
an alert
tone
is emitted:
"beep-beep-,
beep-beep-,beep-beep-'
(Every
"beep-beep-"
has a
time interual
about'1 second)
lnput
voltage
is
abnormal,
too high
or too low
Sheck the
voltage of battery
pack
After
power
on, motor cant
work, such
an
alert tone
is emitted:
"beep-,
beep-,
beep-
"(Every "beep-'has
a time
interval about
2 seconds)
Throttle
signal
is
abnormal
Check the receiver and transmitter
Check
the cable of throttle channel
After
power
on,
motor can't work, such
a
alert
tone
is
emitted:
"beep-,
beep-, beepr'
(Every
"beep-'
has
e time interual about 0.25 second)
Throttle strck is not rn
bottom(
lowest)
position
l\.4ove
the throttle stick to bottom
After
power
on,
motor
cant
work, a
special
tone
'.lstrii"
15 emitted
after 2
The
direction ol throttle channel
is
reversed.
so the ESC has entered
lhe oroqram mode
Set the direction of
throttle
channel
correctly
The motor
runs in opposite direction
The
connection between ESC and
lhe motor need to be chanoed.
Swap
any
two
wire connections
motor
rhmotor
stop
iu;; ng ;hile in working
state
Throttle
sagnal is losl
Check
the
receiver
and transmitter
Check
the
cable
of
throttle channel
ESC
has entered Low
Voltage
Protection mode
Land
RC
model
as soon as
possible,
and
then
16^lo^6 th6 h.tf6^,
^..L
Some
Connections are not reliable
Check
all the connections: battery
pack
connection,
throttle
signal cable, motor connections,
etc.
-t
loro
rEll
Wffi@@ru
Thrgttle
range
s6ttlng:
(Throttle
range should
be reset
when a new transmitter
is being
used)
l-t-"*
;;l
l-"-----,
--"
I l-t-"t-B*t'
,--l
I transmitter. I I oack
to Esc.
I I
should
be emrtled.
I
I move
throttle
ll
and wait
for
| |
means
throttle range
I
I
stick
to top
| |
about2seconos
| |
nignest
poinl
has
been
I
I
I
I
correctlv
confirmed
I
I
6,1,1
rr-.I
l\,4ove throttle
stick
to the
bottom,
several
"beep-'
tones
should
be emitted,
Presenting
the number
of battery
cells
A long
"Beep-'tone
should
be
emitted, means
throttle
range
lowest
point
has
been correctly
confirmed
startup
mode
(1 long
tone)
6.
"beep-*-beep-"
trming
(1
long
1 short)
2. Select
programmable
items:
After entering
program
mode.
you
can
hear B tones
in
a
loop
in the
following sequence.
lf
you
move the throttle
stick to bottom
within 3
seconds
after one
kind of tones,
then
this item will be selected.
(1
short
tone)
battery
type
(2
short
tone)
3.
"beep-beep-beep-' cutoff
mode
(3
short
tone)
4.
"beep-beep-beep-beep-" cutoff threshold
(4
short
tone)
7.
"beep---beep-beep-
set all
to
default
(1
long
2 short)
8.
"beep..--beep--i' exit
(2
long
tone)
Remark: 1 long
"beep----" =
5 short
"beep]
1. Enter
program
mode
1) Switch on
transmitter, move throttle
stick to top
position,
connect
the battery
pack
to ESC
2) Wait for
2 seconds, the
motor should emit
special
tone
Iike
"beep-beep-'
3) Wait for
another 5 seconds,
special tone like
"J567ii"
should
be emitted, which
means
program
mode is entered
4. Exit
program
mode
There are 2 ways
to exit
program
mode:
1. In step
3, after
special
tone
'isie"
,
move
throttle stick
to bottom
within 2 seconds.
2.
ln
step
2,
after
tone
''beep---beep--*.'(ie.
The item
#8),
move
throttle stick
to bottom
within
3
seconds.
3.
Set
item value
(Programmable
value):
You
will hear
several tones
in loop. Set the value
matching
to a tone
by moving throttle
stick
to top when
you
hear the tone,
then a special tone
"i5i."
emits,
means
the value is set
and
saved.
(Keeping the throttle stick at top
position, you
will
go
back
to step 2 and select
other
items; Moving the
stick to bottom within
2 seconds,
you
will exit
the
program
mode directly)
tems
"beePl
1
shorl
tone
"beep-beepJ'
2 short tones 3
short tones
lrake
off
On
lattery type
Li-ion
/ Li-polv
NiMh i Nicd
--.-L'
)utoff mode
Reduce
power
Shut down
-.<aaa
)utoff threshold
Medium
High
itartup mode
Normal
Soft Super soft
liming
Medium High