Instructions / Assembly

ManualsBrandsPleasant Hearth ManualsKitchenVent-Free Fireplace Blower

Questions, problems, missing parts? Before returning to your retail-

er, call our customer service department at 1-877-447-4768, 8:30 a.m.

– 4:30 p.m. CST, Monday – Friday or email us at customerservice@

ghpgroupinc.com.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

IMPORTANT INSTRUCTIONS

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE

W arming Y our Home. Warming Your Heart.

Fireplace System Blower

MODEL #: GFB100

Compatible Fireplace Systems:

VFF-PH20D

VFF-PH26D

VFF-PH32DR

80-10-101

REV. 2013-05-10

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOL-

LOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

WARNING: THIS PRODUCT IS ONLY FOR USE WITH MODELS SPECI-

FIED IN THIS MANUAL BY THE MANFACTURER. ANY OTHER USAGE OR

INSTALLATION NOT SPECIFIED IN THIS MANUAL IS PROHIBITED.

Summary of content (12 pages)

PAGE 1
W a r m i n g Y o u r H o m e. W a r m i n g Y o u r H e a r t. Fireplace System Blower MODEL #: GFB100 Compatible Fireplace Systems: VFF-PH20D VFF-PH26D VFF-PH32DR IMPORTANT INSTRUCTIONS PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. WARNING: THIS PRODUCT IS ONLY FOR USE WITH MODELS SPECIFIED IN THIS MANUAL BY THE MANFACTURER.
PAGE 2
PAGE 3
SAFETY INFORMATION SAVE THESE INSTRUCTIONS WARNING: This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and must be plugged directly into a properly grounded three-prong receptacle. 1. Read all instructions before using this appliance. 3. Do not operate any heater with a damaged cord or plug or after the appliance malfunctions, has been dropped or damaged in any manner. 2. 4. 5. 6. 7. 8. 9. If possible always unplug this appliance when not in use.
PAGE 4
PACKAGE CONTENTS Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and diagram under. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts at 1-877-447-4768. B A C E D F G Parts List REF # A B C D E F G PART # XB001-01 XB002-01Q XB003-01 XB004-01Q PF06-0400-A M4.
PAGE 5
ASSEMBLY INSTRUCTIONS CAUTION: Firebox must be disconnected from gas supply and removed from mantel before installing fan accessory. Contact a qualified service person to do this. 1. Remove Blower Access Panel. 1 Access Panel 2. Mount Blower (B) onto bottom of Fireplace Top using 4 screws (F). 2 3. Attach Power Cord (A) to Blower Access Panel. 3 Screws Power Cord Access Panel 4a. Attach Temperature Sensor (C) to Sensor Bracket using 2 screws, 2 lock washers, and 2 nuts. FF 4b.
PAGE 6
ASSEMBLY INSTRUCTIONS 5. Important: Insert the wires marked with AUTO, OFF and MAN into line slot on the right corner. Keep wires close to the bottom. 5 6. Insert two wires’ female plugs marked with T1 and T2 (black and yellow) into two male ports on Temperature Sensor. 6 7. Insert the female plug on the white power supply wire (marked with P1), into the corresponding male port (marked with P1). 7 8.
PAGE 7
ASSEMBLY INSTRUCTIONS 9. Insert the blower link (male plug) into the power link (female port). 9 10. Important: Bind wires with cable ties (G), and attach cable ties (G) in holes on back of Outer Casing. Attach one in hole near the top and one in hole near the bottom. 10 G Fixed Hole 11. Insert AUTO, OFF, MAN wires through the Rocker Switch opening. 11 12. Connect AUTO, OFF, MAN wires to the three corresponding male ports on the Rocker Switch (E).
PAGE 8
ASSEMBLY INSTRUCTIONS 13. Push Rocker Switch (E) into Control Panel and secure. 13 3 2 E 14. Check that all wires are secure and reattach Blower Access Panel to Outer Casing. Capture the Green Ground wire between the Access Plate and Outer Casing with the upper right screw.
PAGE 9
OPERATING INSTRUCTIONS Using Rocker Switch, turn blower on and check for operation. Turn on Rocker Switch to the desired position. In the MAN position it will remain constantly on. AUTO position will be controlled by the Temperature Sensor. To stop the operation turn Rocker Switch to the OFF position. Electrical Wiring Diagram 2 WHITE ~120V 60Hz GREEN BLACK BLACK 1 5 1. Power Cord 2. Bushing Strain Relief 3. Blower 4. Temperature Sensor 5.
PAGE 10
MAINTENANCE OF MOTORS WARNING: Make sure all power to the appliance is turned OFF before proceeding. Always disconnect the appliance from the main power supply and allow it to cool before any servicing operation. The motor used on the flame blower is prelubricated for extended bearing life and requires no further lubrication. However, periodic cleaning/vacuuming of the appliance around the air intake and exhaust, as well as the blower is recommended.
PAGE 11
This limited warranty is extended to the original retail purchaser of this product and warrants against any This product product product product.
PAGE 12
GHP Group, Inc. 6440 W Howard St Niles, IL 60714-3302 Tel: (877) 447-4768 www.ghpgroupinc.com GHP Group, Inc.