AGES 3+ Thanks for purchasing the SWEET LILY Castle. Please read and retain these instructions. TM 68779 Adult assembly required. WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THE SWEET LILY CASTLE FABRIC. TM This Castle meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the Castle fabric may render the flame resistant properties ineffective.
Fabric Castle Covers T FRON BACK Includes: Also includes: 1 princess dress (fits sizes 3T to 6X) 1 tiara 1 wand 1 frog prince 4x Grey Plastic Tubes 1x Green Plastic Tube 2 x Grey Plastic Connectors 41x Connectors 4 x front bottom connectors (red) 4 x hip corner top connectors (blue) 4 x back corner connectors (red) 4 x hip corner base connectors (blue) 11 x straight connectors (white) 4 x roof corner X connectors (green) 6 x tee connectors (yellow) 4 x roof corner Y connectors (orange) 26x
Assemble Front frame as shown. This will be done in Three steps: 1. Start with the base—just like building a normal house. Front Frame Assembly: #2 Parts required for this step: #2 #3 #1 #1 - All connectors - All white frame tubes 2. Build the castle walls—add all the 3. Build the roof—add the tubes and vertical tubes with the connectors on the top. Add tubes for the top of the walls. Make sure connectors are pushed into the tubes as far as they will go.
Assemble Back frame as shown. This will be done in Three steps: Back Frame Assembly: 1. Start with the base—just like building a normal house. #2 #1 #2 Parts required for this step: #1 - Remaining connectors - All pink frame tubes 3. Build the roof—add the tubes and 2. Build the castle walls—add all the connectors, as shown. The roof will create a four-sided peak. vertical tubes with the connectors on the top. Add tubes for the top of the walls.
SWEET LILY Castle Back Cover Castle Back Cover: 1. 2. 3. Assemble pink frame as shown on page 3. Remove the SWEET LILY Castle back cover from the bag marked “Back.” Completely unzip the cover all the way around. 4. Separate the inside and outside walls by pulling apart the hook-and-loop fasteners (don’t forget the windows!). Parts required for this step: - Completed Frame (pink) 5. - SWEET LILY Castle Back Lay the cover out so both the rectangular red seam and lavender wall face up. 6.
7. Lift the inside wall up and attach it to the frame with the hook-and-loop fasteners. Make sure the bottoms of the strips line up with the bottoms of the pads. 8. 5 17x fasteners Pull out any excess cover from the outside corners of the frame base to make a snug pocket. Pull the cover over the closed end of the frame and across the top of the roof (you may need a helper). The zipper strip should align with the frame.
9. Zip up the cover around the frame. Press the three hook-and-loop fasteners along inside the cover at the top of the frame to keep the roof from sagging. 10. Align and fasten the hook-and-loop fastener around both windows. The back of the castle is now complete.
SWEET LILY Castle Front Cover 1. 2. Castle Front Cover: 3. Assemble white frame as shown on page 2. Remove the SWEET LILY Castle front cover from the bag marked “Front”. Completely unzip the cover all the way around. 4. Unzip the front doors. Parts required for this step: - Completed Frame (white) 6. Lay the cover so the rectangular red seam - SWEET LILY Castle Front 5. T FRON 7 Separate the inside and outside walls by pulling apart the hook-and-loop fasteners. is exposed.
6. Line up the frame on the red seam, as shown. 7. Lift the inside wall up and attach it to the frame with the hook-and-loop fasteners. Make sure the bottoms of the strips line up with the bottoms of the pads.
8. Pull out any excess cover from the outside corners of the frame base to make a snug pocket. Pull the cover with the doors over the closed end of the frame and across the roof (you may need a helper). The zipper strip should align with the frame. 9. Zip up cover around the frame. Press the three hook-and-loop fasteners along inside the cover at the top of the frame to keep the roof from sagging.
10. Fasten the two wide hook-and-loop fasteners around the vertical tubes on both sides of the door. Zip up the door. 11. Unhook the fasteners in the roof turret. Raise the turret by bending the green plastic tube to fit inside. The flat end fits in the middle of the center disk at the bottom and the cone-shaped end faces up. The front of the castle is now complete.
Tower Assembly: 1. Take two grey tubes and one 2. Open the hook-and-eye fasteners in the connector. Insert a tube into each end of connector. Parts required for this step: tower. Insert one end of the tube into the tower up to the the point. Fit the bottom of the plastic tube into the middle of the center disk in the tower floor. - 2 Tower covers - 4 Grey plastic tubes - 2 Grey plastic connectors Storage: 3.
