Wearable Concept 2 Wireless Headset System (WC2) User Guide
Contents Welcome 3 Featured highlights What's in the box 3 4 Overview 5 Headset 5 Bluetooth USB Adapter 5 The Basics 6 Call Controls 6 Mute 7 Adjust the volume 7 Use Smart Sensors 7 Play or pause streaming audio Pair phone or tablet 7 8 Features 9 Listen to Audio via A2DP 9 Transmission Range 9 Simultaneous Call Handling Behavior (PC Mobile) Voice alerts 9 Voice alerts list 9 Voice commands 10 Voice commands list 10 Fit 11 Change the eartip 11 Wear on the left or right 9 11 Charge 12 USB cable
Welcome Congratulations on receiving your new PLT Labs Wearable Concept 2 wireless headset system. This user guide contains instructions for setting up and using your Wearable Concept 2 Bluetooth Headset and BT600 Bluetooth USB Adapter. Featured highlights • Auto Answer calls by placing headset on your ear. • Auto transfers calls between mobile phone and headset. • When on a mobile or PC call, softphone presence is automatically updated.
What's in the box Wearable Concept 2 Bluetooth Headset Portable charge case BT600 Bluetooth USB Adapter Micro USB charge cable with headset charge adapter Desktop charge stand 4
Overview Headset voice Call button Volume button Indicator light (LED) Power button Snap-fit magnetic charge connection Mute button Voice button Play/Pause button Bluetooth USB Adapter Indicator light (LED) 5
The Basics voice Call Controls Answer a call Choose: • Tap the Call button • Put headset on (Smart Sensor) • Say "answer" when prompted (mobile phone only) Answer a second call Choose: • Tap the Call button to end current call, then tap the Call button second call. • Or, for mobile calls, tap the Call button prompted to answer the second call.
Caller Announcement (mobile phone only) When wearing your headset, you will hear the name of a contact calling you so you can decide whether to answer or ignore the call without having to check the phone screen.
Pair phone or tablet Pair your headset to your phone or another device, such as a tablet. 1 Switch on your headset then choose: • Tap the Voice button and say “Pair mode,” or • Press and hold the Call button until you hear “Pairing” 2 While the headset LED is flashing red and blue, activate Bluetooth® on your phone and set it to search for new devices. 3 Select “Wearable_Concept_2.
Features Listen to Audio via A2DP Transmission Range Simultaneous Call Handling Behavior (PC Mobile) Your Wearable Concept 2 headset can play media files (music, podcasts, navigation, etc.) from any A2DP (Advanced Audio Distribution Profile for Bluetooth)-enabled mobile device. Your Wearable Concept 2 Bluetooth headset has a 10 meter effective range. Voice prompts from your headset will alert you if you lose connection with your mobile phone or PC Bluetooth Adapter.
Basic Voice commands Basic Voice commands list Tap the Voice button • • • • • • • • • • • • • • • • • • , wait for command request, then say a command. distance what time is it pair mode talk to cortana launch it redial voice memo secure talk to siri step count unlock talk to google help me hello plantronics no yes answer ignore NOTE The voice-dial feature on your phone is initiated by pressing the Call button for 2 seconds. The voice-dial feature is not a headset voice command.
Fit Change the eartip Change the eartip for a better fit. 1 Push in eartip and rotate to the left to unlock it. 2 1 2 Align new eartip into slot. 3 Push and rotate it to the right to lock it into place. 2 1 Wear on the left or right To wear the headset on your other ear, rotate the boom upwards then twist it around so the eartip is on the other side before lowering the boom.
Charge There are three ways to charge your headset. Your new headset has enough power to pair and make a few calls before charging is needed, though you may charge it at any time. NOTE Always charge at near room temperatures; never charge battery at temperatures below 0°C (32°F) or above 40°C (104°F). 1 2 Align snap-fit magnetic areas of headset and charging device. Attach charging device to USB wall charger or laptop. LED turns off once fully charged. A full charge will take 90 minutes.
Understand the charge case lights The indicator lights flash battery status for the charging case • 3 red flashes = battery critical and the headset . • 2 red flashes = battery low • 2 blue flashes = battery medium • 3 blue flashes = battery full The case indicator lights flash when: • the headset is docked/undocked • the case is connected/disconnected • the battery status button is pressed Test battery status Press the battery status button headset.
Low Battery Warnings Battery Level Tone Voice Prompt 30 minutes of talk time remaining (this alert only occurs during an active call) Double high tone every 15 minutes "Battery Low" repeats every 30 minutes 10 minutes of talk time remaining Triple high tone every 30 seconds "Recharge Headset" every 3 minutes 14
Pairing your Bluetooth USB Adapter Initial Pairing Your Bluetooth USB adapter comes pre-paired to your Wearable Concept 2 headset. Re-Pair USB Adapter to headset In the event that your headset and Bluetooth USB adapter are not paired or become unpaired do the following: 1 2 Remove the Bluetooth USB adapter. Power on your headset then choose one of the following steps: and say "Pair Mode." • Tap the Voice button • Press and hold the Call button Auto Connect until you hear "Pairing.
Connect PC and Call 1 Power headset on. 2 Insert Bluetooth USB adapter directly into your PC USB port. The LED will flash and then turn solid blue to indicate the headset is connected to the USB adapter. The LED remains solid blue when not on an active call. NOTE Insert your Bluetooth USB Adapter directly to your laptop or PC instead of connecting to a USB port on the docking station or hub. 3 Load Plantronics Hub software by visiting plantronics.com/software and click on the "Download" button.
NEED MORE HELP? http://developer.plantronics.com Plantronics, Inc. Plantronics BV 345 Encinal Street South Point Building C Santa Cruz, CA 95060 Scorpius 140 United States 2132 LR Hoofddorp, Netherlands © 2015 Plantronics, Inc. PLT Labs is a trademark of Plantronics, Inc. registered in the US and other countries. Bluetooth is owned by Bluetooth SIG Inc., and any use by Plantronics, Inc. is under license.
