Plantronics Explorer® 200 Series User Guide
Welcome Congratulations on purchasing a Plantronics headset. This User Guide contains instructions for setting up and using your Plantronics Explorer® 200 series headset. Please refer to the separate “For Your Safety” booklet for important product safety information prior to installation or use of the product. Getting Assistance The Plantronics Technical Assistance Centre is ready to assist you.
Contents Welcome ...............................................................................................ii What is Bluetooth®? ............................................................................iv Package Contents, Features and Accessories ..................................... 1 Charging Your Headset ........................................................................ 2 How to Charge Your Headset Using the AC Charger .................. 2 Pairing Your Headset ............................
What is Bluetooth®? Bluetooth wireless technology provides a way for devices to communicate with each other using short-range radio frequency instead of wires. Any two Bluetooth devices can communicate as long as they both have Bluetooth turned on, they are within range and they have been paired — a quick “handshake” process that connects the two devices. Bluetooth range is up to 10 metres (33 feet).
Package Contents and Features Headset Front Call Control Button (on/off) Indicator Light Volume Control Earloop Headset Back Microphone Speaker / Eartip Charging Jack AC Charger 100 – 240V Plantronics Explorer® 200 Series Accessories* Vehicle Charging Adapter #76777-01 USB Headset Charger #76016-01 Vehicle Power Charger #78583-01 * Not included. To order, please contact your Plantronics supplier or go to www.plantronics.
Charging Your Headset 1 2 How to Charge Your Headset Using the AC Charger Before using your headset for the first time, charge it for at least 20 minutes. A full charge takes approximately two hours. 1 2 Connect the AC charger to a power outlet. Plug the AC jack into the charging jack on the headset. While your headset is charging, the indicator glows red. When your headset is fully charged, the indicator turns off. WARNING Do not use your headset while it is connected to the charger.
Pairing Your Headset Pairing is the process of introducing your headset to your phone. Before using your headset for the first time, you must pair it with your Bluetooth phone. Normally, you need to pair your headset with your phone only once. To see a demo of the pairing process, visit www.plantronics.com/ EasyToPair (only available in English). Plantronics QuickPair™ Technology Your new headset includes Plantronics QuickPair technology to simplify the Bluetooth setup process.
Pairing Your Headset—First Time 1 3 SETTINGS Time and Date Phone Settings Bluetooth Sound Settings Network Services 2 BLUETOOTH Discover/ Search 8BK;JEEJ> Security Reset Settings (NNFbWdjhed_Yi PASSKEY 0000 How to Pair Your Phone With Your Headset for the First Time 1 Turn on the Bluetooth feature on your phone. For most phones, select Settings/Tools > Connections > Bluetooth > On. See your phone’s user guide for more information. 2 Turn the headset on.
Pairing Your Headset 2 1 3 BLUETOOTH Discover/ Search 8BK;JEEJ> (NNFbWdjhed_Yi PASSKEY 4 0000 How to Pair Your Headset if it Has Been Previously Paired With Another Device 1 Turn the headset off. Press and hold the call control button until the indicator turns red and then turns off. 2 Turn the headset on. Press and hold the call control button until the indicator light continues to flash red and blue. The headset is now in pairing mode. 3 Use the commands on your phone to locate your headset.
Adjusting the Fit 1 1 Right Left 2 2 1 To remove the earloop, gently pull up on earloop near the Plantronics name until you hear a snap. To replace, gently snap back onto post. 2 3 4 Position earloop as shown above. 5 Align the microphone with the corner of your mouth. Callers can hear you best when you point the microphone towards the corner of your mouth. Place the earloop behind your ear. Rotate the headset so that the speaker/eartip rests comfortably in your ear.
Headset Controls Turn on the headset Press and hold the call control button until the indicator glows blue. You will hear ascending tones. Turn off the headset Press and hold the call control button until the indicator glows red. You will hear descending tones. When power is off, indicator stays off. Answer a call Briefly press the call control button. When you receive a call, your phone may ring before your headset rings.
Headset Controls Transfer a call from headset to phone While in a call, press and hold the call control button until you hear a tone. Transfer a call from phone to headset While in a call, press and hold the call control button until you hear a tone. Range To maintain a connection, keep your headset within 10 metres (33 feet) of the Bluetooth device. If there are obstacles between your headset and the device, you may experience interference.
Indicator Lights Headset Status Headset Indicator Light Powering on Steady blue, then intermittent flashes (changes to standby mode) Powering off Red appears and goes off Standby Blue intermittent flashes Charging battery Red solid light. Light indicator turns off when battery is fully charged and headset is off. Low battery Triple red flashes Pairing mode Blue/red alternating flashes Missed call Purple flashes. Press the call control button to cancel flashing light.
Hands-Free Features If your phone and your wireless service provider both support hands-free operation, you can use the following features: Redial the last number To activate last number redial, double press the call control button. You will hear a double tone after each double-button press. Using Voice Dialling With the headset on, press the call control button for 2 seconds to activate the voice dialling. NOTE To use voice-activated dialling, the voice-dialling feature must be enabled on your phone.
Troubleshooting My headset does not work with my phone. Headset was not in pairing mode when mobile phone menu selections were made. See page 5 “Pairing Your Headset.” Incorrect menu selections were made on your mobile phone. See page 5 “Pairing Your Headset.” I did not enter my passkey. Your phone did not locate the headset. Repeat the pairing process on page 5. Incorrect menu selections were made on your mobile phone. Repeat the pairing process on page 5.
Product Specifications Talk Time* Up to 8 hours Standby Time* Approximately 9 days or 218 hours Charge Time 2 hours Range Up to Bluetooth standard 10 metres (33 feet) Power Requirements 5V DC – 180 mA Battery Type Lithium ion polymer Storage/Usage Temperature 50 °F – 104 °F (10 °C – 40 °C) Version Bluetooth 2.0 Supports Bluetooth hands-free and headset profiles. * Battery enabled. Performance may vary by device.
For safety information, see the separate “For Your Safety” booklet. For warranty information, see the separate “2 Year Warranty” leaflet or visit www.plantronics.com en Plantronics Ltd Wootton Bassett, UK Tel: 0800 410014 ar Middle East Region :تامولعملا نم ديزمل www.plantronics.com cs Czech Republic www.plantronics.
МЛ05 Plantronics, Inc. 345 Encinal Santa Cruz, CA 95060 USA Tlf.: 800-544-4660 www.plantronics.com © 2008 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics Explorer, QuickPair and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth word mark and logo are owned by Bluetooth SIG, Inc. and any use of such marks by Plantronics, Inc. is under license. All other trademarks are the property of their respective owners. U.S.
