0G/5G/2.
Trademarks Copyright © PLANET Technology Corp. 2018. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product.
Table Of Contents 1. Introduction...................................................................... 5 1.1 Package Contents........................................................ 5 1.2 Product Overview........................................................ 6 1.3 Product Features......................................................... 7 1.4 Product Specifications.................................................. 8 2. Hardware Description....................................................... 11 2.
1. Introduction 1.1 Package Contents Thank you for purchasing PLANET 10G Media Converter. In the following sections, unless specified, the term “Media Converter” mentioned in this manual refers to the XT-705A. Open the box of the Media Converter and carefully unpack it. The box should contain the following items: XT-705A Media Converter x 1 User’s Manual x 1 Power adapter (5V, 2.
1.2 Product Overview Flexible and Reliable Network Distance Extension Solution PLANET XT-705A Media Converter is equipped with one 10G/5G/2.5G/1G/100BASE-T auto-negotiation port and one 10GBASE-X SFP+ slot. It supports 10Gigabit Ethernet media conversion from copper 10GBASE-T to fiber multi-mode or single-mode, utilizing 10GBASE-SR or 10GBASE-LR SFP+ transceiver installed in the SFP+ slot to extend distances to servers, switches and patch panels.
fiber cable). It is ideal for applications within the data centers and distributions. Easy Chassis Installation The XT-705A Media Converter can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis (MC-700 and MC-1500 chassis series). The media chassis can assist in providing DC power to the XT-705A Media Converter to maintain the fiber-optic network at one centralized location. It can be DIN-rail or wall mounted for efficient use of cabinet space.
Automatic address learning and address aging Case and Installation External 5V DC, 2.5A power supply DIN-rail and wall-mount design Supports 6000 VDC Ethernet ESD protection 100 meters over Cat 6A / Cat7 at 10Gbps 0 to 50 degrees C operating temperature Co-works with PLANET’s 10”/19” Media Converter Chassis (MC-700/MC-1500/MC-1500R/MC-1500R48) Plug and Play installation 1.4 Product Specifications Model XT-705A Hardware Specifications Copper Interface 1 x 10G/5G/2.
ESD Protection 6KV DC Enclosure Compact-sized metal case Installation Desktop, wall mountable Media convert Chassis installation Optional DIN-rail kit Dimensions (WxDxH) 94 x 70 x 26mm Weight 180g (device only) Power Requirements 5V DC, 2A max. Power Consumption 3.75 watts / 12.8 BTU per hour max. Converter Specifications Flow Control Back pressure for half duplex IEEE 802.3x pause frame for full duplex Fabric 20Gbps Throughput (packet per second) 2.
Network Cables 10G/5G/2.5G/1G/100M BASE-T: 10G--Cat 6A/Cat 7 5G--Cat 6/Cat 6A/Cat 7 1G/2.5G--Cat 5e/Cat 6/Cat 6A/ Cat 7 100M--Cat 5/Cat 5e/Cat 6/Cat 6A/ Cat 7 Cat 5/5e/6/6A/7 UTP cable (100 meters, max.) EIA/TIA-568 100-ohm STP (100 meters, max.) 10GBASE-LR/SR/BX : 50/125μm or 62.
2. Hardware Description 2.1 Physical Dimensions XT-705A dimensions (W x D x H): 94 x 70 x 26mm 10G SFP+ 10GBASE-T to 10GBASE-X 10GBASE-T 5V DC 5G/100 LNK SPD 2.
2.2 Converter Front Panel and LED Indicators Figure 2-2 shows the front panels of the Media Converter. 10G SFP+ LNK SPD 2.5G 10G/1G 10GBASE-T 5G/100 PWR XT-705A 10 Gigabit Ethernet Converter Figure 2-2: XT-705A Front Panel System LED PWR Color Green Function Lit: Power is active Off: Power is inactive Per 10G/5G/2.5G/1G/100BASE-T Port LED Color Green Lit: To indicate that the port is operating at 2.5Gbps. Orange Lit: To indicate that the port is operating at 10/1Gbps. 10/2.
2.3 Rear Panel The rear panel of the XT-705A consists of one DC jack, which accepts input power with 5V DC, 2A. 5V DC Figure 2-3: One DC jack for DC power input 2.4 Power Information: The central pole of the Media Converter’s power jacks measures 2.5mm wide that require +5VDC power input. It conforms to the bundled AC-DC adapter and PLANET’s media chassis. Should you have the issue of power connection, please contact your local sales representative.
2.5mm Width of DC Receptacle: 2.5mm +5V for each slot DC receptacle is 2.5mm wide that matches the central pole; the width of the Media Converter DC jack also measures 2.5mm. Warning: Do not install any improper unit.Converter. The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime.
3. Installation This section describes the functionalities of the Media Converter’s components and guides you to how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 3.1 Stand-alone Installation Step 1: Unpack the Media Converter. Step 2: Connect the 5V DC power adapter to the XT-705A and verify that the Power LED lights up. (Please refer to the 2.4 Power Information section for power input.
4-2: Connect the fiber cable. Attach the duplex LC connector on the network cable to the SFP+ transceiver. Attach the fiber cable from the XT-705A to the fiber network. TX, RX must be paired at both ends. Step 5: When all the connections are all set and the LED lights all show normally, the installation is complete. 3.2 Wall-mount Installation Step 1: Please find Converter the wall that can mount the Media Step 2: Screw two screws on the wall.
Ø4mm XT-705A Switch Bottom Side Step 4: Refer to Chapter 2.4 Power Information on power supply to the Media Converter. to 10GBASE-X 5V DC 10GBASE-T Note Before mounting the device to the wall, please check the location of the electrical outlet and the length of the Ethernet cable. 3.3 Media Chassis Installation To install the Media Converter in a 10-inch or 19-inch standard rack, follow the instructions described below.
1. Never push the converter into the slot with force; it could damage the chassis. Caution 2. The Media Converter Chassis supports hotswap; there is no need to turn off the whole chassis before sliding in the new converter. 3.4 Optional DIN-rail Installation There are two DIN-rail holes on the left side of the XT-705A that allows to be easily installed by DIN-rail mounting. PLANET optional DIN-rail mounting kit – RKE-DIN -- can be ordered separately.
Step 3: Check whether the DIN rail is tightly on the track. Caution You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty. 3.5 Cable Connection Installing the SFP+ Transceiver The sections describe how to insert an SFP+ transceiver into an SFP+ slot. The SFP+ transceivers are hot-pluggable and hot-swappable.
Note It is recommended to use PLANET SFP+s on the Media Converter. If you insert an SFP+ transceiver that is not supported, the Media Converter will not recognize it. 10GBASE-X SR/LR: Before connecting the other switches, workstation or Media Converter, please do the following: 1. Make sure both sides of the SFP+ transceiver are with the same media type; for example, 10GBASE-SR to 10GBASE-SR, 10GBASE-LR to 10GBASE-LR. 2. Check whether the fiber-optic cable type matches the SFP+ transceiver model.
disable the port in advance. 2. Remove the fiber optic cable gently. 3. Turn the lever of the MTB module to a horizontal position. 4. Pull out the module gently through the lever. MTB Series Transceiver 1 2 Figure 3-5-2: Pulling Out from the Transceiver Note Never pull out the module without pulling the lever or the push bolts on the module. Directly pulling out the module with effort could damage the module and SFP+ module slot of the Media Converter. 10G/5G/2.5G/1G/100BASE-T The 10G/5G/2.
Connecting the UTP Cable The 10G/5G/2.5G/1G/100BASE-T port uses RJ45 socket -similar to phone jack -- for connection of unshielded twistedpair cable (UTP). The 802.3u/802.3ab/802.3bz/802.3ae Ethernet standard requires Category 5 UTP for 100Mbps 100BASE-TX. 10G/5G/2.5G/1G/100BASE-T uses Cat5e/6/6A/7 UTP (see table below). Maximum distance is 100 meters (328 feet). Standard Transfer Speed 10GBASE-T 10000Mbit/s Cat 6A/7 5GBASE-T 5000Mbit/s Cat 6/6A/7 2.
4. Troubleshooting This chapter contains information to help you solve issues. If the Media Converter is not functioning properly, make sure the Media Converter is set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Media Converter. Performance is bad Solution: Check the speed duplex mode of the partner device. The Media Converter usually runs in auto-negotiation mode. If the partner is set to half duplex, the performance will be poor.
Can I install MTB-TSR or the other industrial-grade SFP+ module with non-wide temperature feature into the SFP+ slot of Media Converter? Solution: Yes, you can. However, the XT-705A features non-wide temperature, meaning it cannot be operated with temperature ranging from -40 to 75 degrees C. PLANET recommends customers to use the IXT-705AT industrialgrade 10G Media Converter with the wide-ranging operating temperature feature.
Appendix A: Approved PLANET SFP+ Transceivers PLANET Media Converter supports 100/1000 dual mode with both single mode and multi-mode SFP+ transceivers.
Appendix B: Networking Connection B.1 Converter’s RJ45 Pin Assignments 1G, 2.
B.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
EC Declaration of Conformity For the following equipment: *Type of Product : 10G/5G/2.5G/1G/100M Copper to 10GBASE-X SFP+ Media Converter *Model Number : XT-705A * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.
