User's Manual
Table Of Contents
- Chapter 1 INTRODUCTION
- Chapter 2 INSTALLATION
- Chapter 3 witch Management
- Chapter 4 Basic Switch Configuration
- Chapter 5 File System Operations
- Chapter 6 Cluster Configuration
- Chapter 7 USB Function Configuration
- Chapter 8 Device Management
- Chapter 9 Port Configuration
- Chapter 10 Port Isolation Function Configuration
- Chapter 11 Port Loopback Detection Function Configuration
- Chapter 12 ULDP Function Configuration
- Chapter 13 LLDP Function Operation Configuration
- Chapter 14 Port Channel Configuration
- Chapter 15 MTU Configuration
- Chapter 16 bpdu-tunnel-protocol Configuration
- Chapter 17 DDM Configuration
- Chapter 18 EFM OAM Configuration
- Chapter 19 LLDP-MED
- Chapter 20 PORT SECURITY
- Chapter 21 QSFP+ Port Split and Combination Configuration
- Chapter 22 VLAN Configuration
- Chapter 23 MAC Table Configuration
- Chapter 24 MSTP Configuration
- Chapter 25 QoS Configuration
- Chapter 26 PBR Configuration
- Chapter 27 IPv6 PBR Configuration
- Chapter 28 Flow-based Redirection
- Chapter 29 Egress QoS Configuration
- Chapter 30 Flexible QinQ Configuration
- Chapter 31 Layer 3 Management Configuration
- Chapter 32 ARP Scanning Prevention Function Configuration
- Chapter 33 Prevent ARP, ND Spoofing Configuration
- Chapter 34 ARP GUARD Configuration
- Chapter 35 Gratuitous ARP Configuration
- Chapter 36 DHCP Configuration
- Chapter 37 DHCPv6 Configuration
- Chapter 38 DHCP option 82 Configuration
- Chapter 39 DHCPv6 option37, 38
- Chapter 40 DHCP Snooping Configuration
- Chapter 41 DHCP option 60 and option 43
- Chapter 42 IPv4 Multicast Protocol
- Chapter 43 IPv6 Multicast Protocol
- Chapter 44 Multicast VLAN
- Chapter 45 ACL Configuration
- Chapter 46 Self-defined ACL Configuration
- Chapter 47 802.1x Configuration
- 47.1 Introduction to 802.1x
- 47.2 802.1x Configuration Task List
- 47.3 802.1x Application Example
- 47.4 802.1x Troubleshooting
- Chapter 48 The Number Limitation Function of MAC and IP in Port, VLAN Configuration
- 48.1 Introduction to the Number Limitation Function of MAC and IP in Port, VLAN
- 48.2 The Number Limitation Function of MAC and IP in Port, VLAN Configuration Task Sequence
- 48.3 The Number Limitation Function of MAC and IP in Port, VLAN Typical Examples
- 48.4 The Number Limitation Function of MAC and IP in Port, VLAN Troubleshooting Help
- Chapter 49 Operational Configuration of AM Function
- Chapter 50 Security Feature Configuration
- 50.1 Introduction to Security Feature
- 50.2 Security Feature Configuration
- 50.2.1 Prevent IP Spoofing Function Configuration Task Sequence
- 50.2.2 Prevent TCP Unauthorized Label Attack Function Configuration Task Sequence
- 50.2.3 Anti Port Cheat Function Configuration Task Sequence
- 50.2.4 Prevent TCP Fragment Attack Function Configuration Task Sequence
- 50.2.5 Prevent ICMP Fragment Attack Function Configuration Task Sequence
- 50.3 Security Feature Example
- Chapter 51 TACACS+ Configuration
- Chapter 52 RADIUS Configuration
- Chapter 53 SSL Configuration
- Chapter 54 IPv6 Security RA Configuration
- Chapter 55 VLAN-ACL Configuration
- Chapter 56 MAB Configuration
- Chapter 57 PPPoE Intermediate Agent Configuration
- Chapter 58 SAVI Configuration
- Chapter 59 Captive Portal Authentication
- 59.1 Captive Portal Authentication Configuration
- 59.2 Accounting Function Configuration
- 59.3 Free-resource Configuration
- 59.4 Authentication White-list Configuration
- 59.5 Automatic Page Pushing after Successful Authentication (it is not supported currently)
- 59.6 http-redirect-filter
- 59.7 Portal Non-perception
- 59.8 Portal Escaping
- Chapter 60 VRRP Configuration
- Chapter 61 IPv6 VRRPv3 Configuration
- Chapter 62 MRPP Configuration
- Chapter 63 ULPP Configuration
- Chapter 64 ULSM Configuration
- Chapter 65 Mirror Configuration
- Chapter 66 RSPAN Configuration
- Chapter 67 SNTP Configuration
- Chapter 68 NTP Function Configuration
- Chapter 69 DNSv4/v6 Configuration
- Chapter 70 Summer Time Configuration
- Chapter 71 Monitor and Debug
- Chapter 72 Reload Switch after Specified Time
- Chapter 73 Debugging and Diagnosis for Packets Received and Sent by CPU
- Chapter 74 VSF
- Chapter 75 SWITCH OPERATION
- Chapter 76 TROUBLESHOOTING
- Chapter 77 APPENDIX A
- Chapter 78 GLOSSARY
Configuration Guide of XGS-5240-Series
39-2
2. Dhcpv6 relay option basic functions configuration
3. Dhcpv6 server option basic functions configuration
1.DHCPv6 snooping option basic functions configuration
Command
Description
Global mode
ipv6 dhcp snooping remote-id option
no ipv6 dhcp snooping remote-id option
This command enables
DHCPv6 SNOOPING to
support option 37 option, no
command disables it.
ipv6 dhcp snooping subscriber-id option
no ipv6 dhcp snooping subscriber-id option
This command enables
DHCPv6 SNOOPING to
support option 38 option, no
command disables it.
ipv6 dhcp snooping remote-id policy {drop | keep |
replace}
no ipv6 dhcp snooping remote-id policy
Th
is command is used to
configure the reforward policy
of the system when receiving
DHCPv6 packets with option
37, which can be:
drop,
the system simply
discards it with option 37;
keep, the system keeps option
37 unchanged and forwards
the packet to the server;
replace, the system replaces
option 37 of current packet with
its own before forwarding it to
the server. no command
configures the reforward policy
of DHCPv6 packets with option
37 as replace.
ipv6 dhcp snooping subscriber-id policy {drop |
keep | replace}
no ipv6 dhcp snooping subscriber-id policy
This command is used to
configure the reforward policy
of the system when receiving
DHCPv6 packets with option
38, which can be:
drop,
the system simply
discards it with option 38;