WGSW-Series (V3) User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Port Isolation
- 4.3.3.7 VLAN setting example:
- 4.3.3.7.1 Two Separate 802.1Q VLANs
- 4.3.3.7.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.7.3 Port Isolate
- 4.3.3.8 MAC-based VLAN
- 4.3.3.9 IP Subnet-based VLAN
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Power over Ethernet (For WGSW-20160HP/24040HP/24040HP4)
- 4.7 ONVIF
- 4.8 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
- EC Declaration of Conformity
User’s Manual of WGSW-24040 and 24040HP Series Managed switch
31
LED
Color
Function
PWR
Green
Lights
To indicate that the Switch has power.
■ Alert
LED Color Function
FAN1
Green
Lights
To indicate that FAN1 has failed.
FAN2
Green
Lights
To indicate that FAN2 has failed.
FAN3
Green
Lights
To indicate that FAN3 has failed. (For WGSW-24040HP4 only)
PWR
Green
Lights
To indicate that the power has failed.
Per 10/100/1000Mbps port with PoE interfaces
LED Color Function
LNK/ACT
Green
Lights:
To indicate the link through that port is successfully established at
10/100/1000Mbps.
Blink:
To indicate that the Switch is actively sending or receiving data over that port.
PoE In-Use
Orange
Lights:
To indicate the port is providing 56V DC in-line power.
Off:
To indicate the connected device is not a PoE powered device (PD).
Per 100/1000Mbps SFP Combo Interface (Port -21 to Port-24)
LED Color Function
1000 Green
Lights To indicate the port is successfully established at 100/1000Mbps.
100 None
LNK/ACT Orange
Blink:
To indicate that the Switch is actively sending or receiving data over that port.
WGSW-20160HP LED Indication Table
■ System
LED
Color
Function
PWR
Green
Lights to indicate that the Switch has power.
SYS
Green
Lights to indicate the system is working.
■ Alert
LED Color Function
FAN1
Green
Lights to indicate the FAN1 failure.
FAN2
Green
Lights to indicate the FAN2 failure.
Per 10/100/1000Mbps port with PoE interfaces (Port-1 to Port-16)
LED Color Function
LNK/ACT Green
Lights: To indicate the link through that port is successfully established at
10/100/1000Mbps.
Blink: To indicate that the Switch is actively sending or receiving data over that port.
PoE In-Use Orange
Lights: To indicate the port is providing 56V DC in-line power.
Off: To indicate the connected device is not a PoE Powered Device (PD).