WGSW-Series (V3) User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Port Isolation
- 4.3.3.7 VLAN setting example:
- 4.3.3.7.1 Two Separate 802.1Q VLANs
- 4.3.3.7.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.7.3 Port Isolate
- 4.3.3.8 MAC-based VLAN
- 4.3.3.9 IP Subnet-based VLAN
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Power over Ethernet (For WGSW-20160HP/24040HP/24040HP4)
- 4.7 ONVIF
- 4.8 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
- EC Declaration of Conformity
User’s Manual of WGSW-24040 and 24040HP Series Managed switch
25
Product WGSW-20160HP WGSW-24040HP WGSW-24040HP4
Hardware Specifications
Hardware Version 2
Copper Ports
16 10/ 100/1000BASE-T
RJ45 auto-MDI/MDI-X
ports
20 10/ 100/1000BASE-T RJ45 auto-MDI/MDI-X
ports
10/100/1000Mbps / SFP Combo
Interfaces
4 10/100/1000Mbps TP and SFP shared combo interfaces, SFP (Mini-GBIC)
supports 100/1000Mbps dual mode DDM
Console 1 x RJ45 serial port (115200, 8, N, 1)
Switch Architecture Store-and-Forward
Switch Fabric 40Gbps / non-blocking 48Gbps / non-blocking
Throughput 29.8Mpps@64Bytes 35.7Mpps@64Bytes
Address Table 8K entries, automatic source address learning and ageing
Shared Data Buffer 4 megabits
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 9K bytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory Default
Power Requirements
100~240V AC, 50/60Hz,
4A
100~240V AC, 50/60Hz,
4A
100~240V AC, 50/60Hz,
6A
Power Consumption (Full Loading)
252 watts 262 watts 482 watts
ESD Protection
6KV DC
Dimensions (W x D x H)
440 x 200 x 44.5 mm, 1U high
Weight 4.1kg 4.25 kg 4.75 kg
Layer 2 Management Function
PoE Standard
IEEE 802.3at/802.3af Power over Ethernet
PoE Power Supply Type
End-span
PoE Power Output Per port 52V DC, 590mA. max. 30.8 watts
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget
220 watts max. 220 watts max. 440 watts max.
PoE Ability
7 watts
16 units 24 units 24 units
15 watts 14 units 14 units 24 units
30 watts 7 units 7 units 14 units
Layer 2 Management Function
Basic Management Interfaces Console; Telnet; Web Browser; SNMP v1, v2c
Secure Management Interfaces SSH, SSL, SNMP v3
Port Configuration
Port disable / enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection