Datasheet
WGSD-10020HP
2
–
IP Subnet-based VLAN
–
Voice VLAN
–
Management VLAN
• Supports SpanningTreeProtocol
–
STP, IEEE 802.1D Spanning Tree Protocol
–
RSTP, IEEE 802.1w Rapid Spanning Tree Protocol
–
MSTP, IEEE 802.1s Multiple Spanning Tree Protocol
–
STP BPDU Guard and BPDU ltering
• Supports LinkAggregation
–
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
–
Cisco ether-channel (Static Trunk)
–
Maximum 5 trunk groups, up to 5 ports per trunk group
–
Up to 20Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Port Mirroring to monitor the incoming or outgoing trafc on
a particular port
• Loop protection to avoid broadcast loops
Layer 3 IP Routing Features
• Supports maximum 32 software static routes and route
summarization
Quality of Service
• Ingress Shaper and Egress Rate Limit per port bandwidth
control
• 8 priority queues on all switch ports
• Trafc classication
–
IEEE 802.1p CoS
–
TOS / DSCP / IP Precedence of IPv4/IPv6 packets
–
IP TCP/UDP port number
–
Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS
policies
• Trafc-policing policies on the switch port
• DSCP remarking
Multicast
• Supports IGMP snooping v1, v2 and v3 for IPv4 multicasting
network
• Supports MLD snooping v1 and v2 for IPv6 multicasting
network
• Querier mode support
• IGMP snooping port ltering
• MLD snooping port ltering
• MVR (Multicast VLAN Registration)
Intelligent Powered Device Alive Check
The WGSD-10020HP PoE Gigabit Managed Switch can be congured to monitor
connected PD (Powered Device) status in real-time via ping action. Once the
PD stops working and responding, the WGSD-10020HP will recycle the PoE
port power and bring the PD back to work. It will greatly enhance the network
reliability through the PoE port resetting the PD’s power source and reduce
administrator management burden.
PoE Schedule for Energy Saving
Under the trend of energy saving worldwide and contributing to environment
protection on the Earth, the WGSD-10020HP can effectively control the power
supply along with its capability of giving high watts power over Ethernet. The
“PoEschedule” function enables you to activate or inactivate PoE power feeding
for each PoE port during specified time intervals, which is a powerful function to
help SMBs or enterprises save power and money.
Solution for IPv6 Networking
By supporting IPv6 / IPv4 dual stack and plenty of management functions with
easy and friendly management interfaces, the WGSD-10020HP is the best choice
for IP surveillance, VoIP and wireless service providers to connect with the IPv6
network. It also helps SMBs to step in the IPv6 era with the lowest investment
but not necessary to replace the network facilities while the ISP constructs the
IPv6 FTTx edge network.
IPv4 and IPv6 Software VLAN Routing for Secure and Flexible
Management
To help customers stay on top of their businesses, the WGSD-10020HP not only
provides ultra high transmission performance and excellent layer 2 technologies,
but also offers IPv4/IPv6 SoftwareVLANrouting feature which allows to cross
over different VLANs and different IP addresses for the purpose of having a highly
secured, exible management and simpler networking application.
PT PoE Camera
Ping Request
Ping Request
Check alive status for 3 times
Restart PoE device if without response
Ping Echo
No Response......
PD Alive!!
Step 1
Step 3
Step 2
Step 4
ON
PoE
ON
ON
PoE
OFF
PD Status
Good!!
Alarm Notification
Power
On
Power
On
Power
On
Power
On
6 Watts 6 Watts 12 Watts 12 Watts
PoE
PoE PoE
PoE
Power
Off
Power
Off
Power
Off
Power
On
6 Watts 6 Watts 12 Watts 12 Watts
PoE
PoE PoE
PoE
PoE
1000Base-T UTP with PoE
Total consumption of 36 watts/hr
5PM8AM
5PM 8AM
Save 24 watts/hr during off-business hours
Total Saved = 10800 Watts/month